User manual BINATONE T430BT

[. . . ] User Guide T430BT 2nd edition www. binatonegps. com Binatone Navigation software IMPORTANT Satellite signals are required for this product to function in Navigation Mode. There may be occasions within your home or surrounding area when the signal strength is limited and Navigation Mode may not be possible. If you experience difficulty in receiving a signal in your car you may need to use an external antenna (optional). The Help Line is available from 9:00 am to 5:00 pm, Monday to Friday, on 0845 345 9677 Calls are charged at Local Call rate (for UK only). [. . . ] Last Call Redial You can easily redial the number of the last call you received, from the Bluetooth main menu tap . 23 SETUP Use of the Mounting Kit Take the following steps to mount the unit in the vehicle using the supplied mounting kit (mount bracket, mount cradle, etc. ): Fig. Lift the suction lever, and place the unit on the desired location, then press down and push the lever down to secure the suction cup. Rotate the bracket arm to adjust the unit to obtain a good view of the display. If you want to remove the unit, press the tab at the bottom of the mounting cradle (see right figure). Warning: The device must not be mounted so that it impairs the driver's view of the road. Please take extra precaution to ensure that any airbags are not obstructed by the device. 24 NAVIGATION MENU Navigation Getting Started Please make sure that the battery in your device is charged. You will first see the warning statement screen tap on "I accept" to confirm that you have read the statement and to continue. If you do not wish to be shown this screen in the future check the box next to "Don't show this statement again". You will now be shown the Binatone screen, which shows the progress of the loading software on the yellow bar at the bottom. Once the software has loaded you will be shown the navigation main menu, this is the starting point for all your navigating needs. 25 NAVIGATION MENU Navigate to ­ Opens the destination page. From here you can select a point to navigate to or you can select a start/destination point and then simulate the route between them, just as if you were driving it. You can also gain access to the route options so that you can set your driving preferences. Go Home ­ This allows you to navigate to your home in one simple button press. Note: you will have to first set your home address via the settings menu first. Edit Favourites ­ Allows you to add and edit locations of interest to you, so that they can be quickly used again for navigating to. Recent Destinations ­ A list which keeps a record of all the destinations you have recently entered, so that they can be quickly used again for navigating to. View Map ­ allows you to view any part of the installed map, handy so that you can have a detailed view of the area around your selected destination before you set off. Settings ­ allows access to the main setting of the unit, which you can set to you personal preference. Exit ­ Exits from navigation mode back to the unit's main menu. Satellite Signal Indicator ­ allows you to quickly view the status of the GPS signal. Green means a GPS lock is obtained, Grey means that a GPS lock cannot be currently achieved. Time bar ­ Shows the current time and data as automatically set by the received satellite signals. Also allows for access to the Time Zone setting when tapped. Bluetooth ­ the icon is located in the top right of the screen and allows direct access to the Bluetooth menu. 26 NAVIGATION MENU Navigate to Tap this option to begin any journey or if you wish to set up a route simulate. Navi ­ Used to navigate to a destination, via a number of waypoints if also set. Route options ­ Opens the route options menu allowing you to set your preferred driving preferences. Up/Down arrow ­ Used to scroll to view the list of waypoints/destination which are currently not shown. Move Up/Down ­ Use to shift the position of the waypoints/destination you have entered. On Map ­ Use to view the selected waypoint/destination on the map. [. . . ] In order to navigate you need at least 4 locked satellite signals which will give a 3D fix. This is clearly indicated at the bottom of the screen by either the word Invalid or valid 47 NAVIGATION MENU Time Zone Setting The time on the unit is automatically set by the satellite signals, but in order to correct this time for your current location you will need to set the time zone. The default time zone is GMT, but during the period of the last Sunday in March to the last Sunday in October you will have to change this setting to BST. This only needs to be done when located in the UK. To change the time zone setting tap on the time and date in the main menu. [. . . ]