User manual BINATONE MR620

[. . . ] As long as the handset is in VOX mode, VOX is shown steadily on the display. 1 2 3 MENU button Press to change Channels and sub-channels, and to switch between modes ON/OFF button SCAN VX O DCM To fit the batteries Do not remove the sleeve from the battery pack. 2. Insert the battery pack making certain that the arrow is showing & pointing towards the top of the handset. Plug the mains adaptor into a 230V AC , 50Hz main socket with the switch on the socket set to OFF. Then switch on the main socket. Using any other adaptor will result in non-compliance with EN60065 and will invalidate any approvals & warranty. Important safety warning To reduce radio frequency exposure when you're using your MR620, hold the handset at least 5cm(2inches)from your face. Keep the MR620 out of the reach of babies and young children. Press the TALK button to confirm the sub-channel setting. 1 Transmitting and Receiving. [. . . ] when the bars reduce, the battery needs charging Shown when you are transmitting the signal Shown when you are receiving the signal Dual watch-shown when you are monitoring two channels at once. Shown when the unit is in VOX (voice activated mode) Shown when the unit is scanning all channels Shown when the buttons are locked Volume level Important _ read these Safety Warning before you charge the batteries When placing the handset in the charger, use only the rechargeable battery pack supplied with the MR620. Make sure the battery compartment cover is securely locked in place when you are charging the batteries. Dispose of used batteries safely and in a way that will not harm the environment _ never try to burn them or put them anywhere, they could get burnt or punctured. They might leak if you do. 1 It takes about 10 hours to recharge the batteries fully if they've become completely run down. Battery meter The battery meter is located in the left corner of the LCD panel. When the battery level reaches its minimum level, the handset will emit two beep tones and automatically turn OFF the power. Battery life The MR620 has a built in power saver feature to make the batteries last longer. But when you are not using the handset, it's better to switch it off to save the battery power. Selecting Call-Ring tones Press the MENU button four times, the unit will enter MENU Call-Ring setting mode. (5 different tones), the different Call-Ring tones can be heard during changing. TALK 2 Changing the channels and sub-channels MR620 has eight channels, numbered 1to8. To communicate with other PMR users within range, you must all have your PMR tuned to the same channel. Press the MENU button once 1 MENU The current channel number flashes on the display 2 3 TALK 3 Press the TALK button to confirm your setting after you select your desired Call-Tone. Press the TALK button to stop monitoring. Setting Call-Ring off If you don't want to hear the call tone, you can set Call-Ring mode to OFF. In this stage, you can send the Call-Ring(default Call-Ring number 1) to the other party, but you will not hear the tone. Press the UP or DOWN buttons to go to the channel you want Press the TALK button to confirm the channel setting. Binatone Help Line: 0845 345 9677 Each channel also has 38 sub-channels(sometimes call CTCSS codes) letting you set up groups of users within the same channels, for more private communication. If you have set sub-channel, you can Binatone Help Line: 0845 345 9677 1 MENU Press the MENU button four times, the unit will enter Call-Ring setting mode. Press the UP or DOWN button until "OF " is shown on the display. TALK 2 3 TALK Built-in Flashlight As an added feature, your MR620 has a built-in flashlight. Press and release the FLASH LIGHT button to turn the light ON and OFF. 6. Guarantee and service The Binatone MR620 is fully guaranteed for 12 months from the date of purchase shown on your sales receipt. The guarantee does not cover damage by misuse or negligence, or by excessive voltages. If you see any damage, don't use the handsets-return the whole system to where you bought it . If your Binatone MR620 develops a fault, first check the points in the troubleshooting section. If you can't solve the problem, return the whole system as follows; 7. [. . . ] 3 Return your MR620 to the address given by the Service Department, making sure you include your name and address, and a cheque or postal order for the value of the repair charge. This does not affect your statutory rights. Dual-Watch-Monitor the current channel plus one other at the same time. 2 3 4 5 TALK MENU VOX sensitivity is too low set it to a higher level Speak in a louder voice, nearer to the microphone Make sure the mains power lead is firmly plugged into the charger. Make sure the mains power adapter is plugged in, and that mains power is switched on at the socket. [. . . ]