User manual BINATONE LYRIS 410

[. . . ] Place the Handset on the cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset. Set Time/Date Insert the rigid clips of the stand into the slots on the bottom of the phone (near the rear of the base). To remove the stand, (1) pinch the flexible clips, ( 2) pull back the stand, and then (3) slide up and forward (3) as shown below. 1 2 3 4 5 6 You will need to set the correct time and date so they can be displayed correctly on the display. If you subscribe to a Caller Display service, the time and date will be set automatically on receipt of your first incoming call. The display shows ' SET 1 DATE '. Press SET/STO button to confirm. [. . . ] Press SET/STO to confirm. Press UP or DOWN button to select your comfortable display viewing level (1~8). The display shows ' SET 2 LCD ' , you can continue with programming, or press DELETE button to return to standby mode. 4. Lift the Handset and check for Dial tone in the earpiece. and 08453459677 0818762092 03 to Modular Wall jack inatoneonline. com/ Mark two points on the wall that are 92 mm apart to lay the fixing centers as shown below. 5 Set Flash Time 1 2 3 4 5 This telephone gives you the possibility to use the special services services of your network provider. When pressing the RECALL button, the phone generates a line interruption and the length depends on your Flash Time setting. Press UP or DOWN button until the display shows 'SET 3 FLASH'. The display shows ' SET 1 DATE ' , you can continue with programming, or press DELETE button to return to standby mode. Lift the Handset, listen for a dial tone. The display shows the number as you dial(maximum of 14 digits will be shown). When the phone rings; Lift the handset or press the SPEAKERPHONE button on the Base unit. The Call timer starts about 7 seconds after going on line. Dial out Stored number Storing a Number in (0-9) two-touch memories 1 2 3 2 3 Lift up Handset or press the SPEAKERPHONE button, press M1, M2, M3 buttons. The number dials automatically. In standby mode, Key in the telephone number you wish to stored. Press SET/STO button. Press the (0-9) button to store the number in the selected memories. After the Guarantee has expired If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair under Guarantee. Call our Service Department on 0845 345 9677 and ask for a quotation of the repair charge and details of where to send your Lyris 410 for repair. Return your Lyris 410 to the address given by the Service Department. 8. Technical details Standard Lyris 410 Telephone Temperature range Operating 0 ºC to 40 ºC Storage -20 ºC to 60 ºC PBX compatibility Timed break recall: 98 ms. Signalling type: DTMF (dual-tone multifrequency) also called tone dialing. Network connection This equipment is intended to be used in the UK only. Operation on other countries' PSTN termination points cannot be guaranteed. BINATONE TELECOM PLC 1 Apsley Way London NW2 7HF, United Kingdom. Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877 e-mail: binatoneuk@binatonetelecom. co. uk ________________________________________ 5. [. . . ] Declare under our sole responsibility that the following product Type of equipment: Corded phone Model Name: Lyris 410 Country of Origin: China Brand: Binatone complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the approximation of the laws of the Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC) and the European Community Directive 2006/95/EC relating to Electrical Safety. Assessment of compliance of the product with the requirements relating to the essential requirements according to Article 3 R&TTE was based on Annex III of the Directive 1999/5/EC and the following standard: Waste electrical products must not be EMC: EN 55022:2006 disposed of with household waste. EN 55024:1998+A1+A2 Electrical Safety: EN 60950-1:2006 The product is labelled with the European Approval Marking CE as show. Manufacturer / Importer (signature of authorized person) This equipment should be taken to your local recycling centre for safe treatment. Last Number Redial Mute Function 1 2 1 2 Viewing the 1 Caller Display list 2 To return a call 1 2 Inserting a Pause in the dialing sequence 1 2 Use on PBX Storing a Number in M1, M2, M3 memories 1 For some switchboard system, an access number must be dialed (usually an 8 or 9) to get another dial tone and an outside line. Pressing PAUSE button immediately after the access number, a pause of about 3. 6 seconds will be entered, and the desired number can be dialed immediately. [. . . ]