User manual BINATONE ICARUS 200 SYSTEM

[. . . ] TECHNICAL DETAILS Standard Digital Enhanced Cordless Telecommunication (DECT) 1. 88 to 1. 9 GHz (bandwidth = 20 MHz) 1. 728 MHz Up to 300m outdoors; up to 50m indoors Standby: 100 hours Talking: 10 hours Battery charge time:15 hours Operating 0 C to 40 C Storage -20 C to 60 C HANDSET 500mAH NiMH TABLE OF CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1 5 PRIVATE PHONEBOOK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6 5. 1 5. 2 5. 3 5. 4 5. 5 5. 6 5. 7 ADD A NEW PHONEBOOK ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SEARCH A PHONEBOOK ENTRY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 VIEW A PHONEBOOK ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The respective ringtone will be played when browsing the ringtone list. (Note: the selected melody will only be played if you subscribe to Caller Display and the incoming number matches the stored number. ) 7. 4. 9 Find the Handset You can locate the handset by pressing <PAGE> on the base station. All the handsets registered to the base will produce the paging tone and show "PAGING" on the display. You can stop the paging by pressing <TALKON>/ <TALK OFF> /<C> on any handset or <PAGE> on the base again. Note: If there is an incoming call during paging, the phone will ring with the incoming call instead of paging. 4. 10 Make an Internal Call (For Multi-handset Versions Only) This feature is only applicable when there are at least two registered handsets. It allows you to make internal calls, transfer external calls from one handset to another handset and make conference calls. If the called handset is not in answered with 60 seconds, the called handset will stop ringing and the calling handset will return to standby mode. Note: If only one handset is registered to the base station, when <C/MUTE/INT> is pressed, it will display "NOT POSSIBLE" 4. 10. 1 Intercom Another Handset 1. In idle mode, press <C/MUTE/INT> and all the other registered handset numbers will display, along with a "9". Enter the number of the handset that you want to call, or enter "9" to call all handsets. The called handset rings and <TALK ON> must be pressed on that handset to establish the intercom call. Note: If only two handsets are registered to the base station, pressing <C/MUTE/INT> will call the other handset immediately. In idle mode, press <C/MUTE/INT> and the registered handsets will display. Press <KEY 9> to ring to all registered handsets 4. 10. 3 Transfer an External Call to another handset During an external call: 1. Press <OK> to show all the other registered handset numbers, plus "9". The external call is put on hold automatically and the called handset rings . Press <TALK ON> pressed on that handset on the on the called handset to establish an internal call. Press <TALK OFF> on the calling handset or put the calling handset on the charging cradle to end the current call with the external party. 4. 10. 4 Make a 3-way Conference Call The conference call feature allows one external call to be shared with two handsets (in intercom). The three parties can share the conversation and no additional network subscription is required. [. . . ] 7. 6 Reset Your Phone You can reset your phone to the default settings . After a reset, all your personal settings and call list entries will be deleted, but your phonebook remains unchanged. Press <OK> and you are requested to enter the 4-digit system PIN. Press <OK> to confirm, and the phone will be reset to its default settings. The call does not work. [. . . ]