User manual BINATONE FUSION 2200

[. . . ] 10 Intercom, transfer & conference If you have a Fusion 2200/2210 Twin, Triple or Quad system, you already have two, three or four handsets. Altogether, you can have up to five handsets registered to the base unit, as numbers 2, 3, 4 and 5. With more than one handset registered to your base unit, you can make intercom calls from one handset to another, make a new intercom call while you are on an outside call shuttle between an outside call and an intercom call transfer an outside call from one handset to another set up a three-way conference call between yourself, an outside call and an intercom call Each handset has its own number -- 1, 2, 3, 4 or 5 -- which is shown on the right-hand side of the display. Please note -- Among the handsets registered to a single base unit, only one outside call and two intercom calls can take place at once. [. . . ] It will help if you have your PBX work properly on documentation to hand when you make the call. a PBX. " Intercom and transfer Move the handset closer to the base unit, or to a different position. Try moving the base unit so that it's not near other electrical equipment, such as a TV or a computer. If you are using a routing box (smart socket), try disconnecting it then making a call. If the sound is OK without the routing box, that's the cause of the problem. You'll get the best results if you site the base unit as high as possible. For example, in a two-storey house, the first-floor landing is an ideal place for the base unit. Disconnect the mains power lead from the back of the base unit, then wait for 30 seconds before reconnecting it. "I can't transfer a call. " Make sure the other handset is within range of the base unit, and is not busy on a call. Make sure you are keying in the correct number (1 to 5) for the other handset. If the fault persists . . . Disconnect all other instruments connected to the same line as the Fusion 2200/2210 and see whether you can make a call. Batteries "The handset`s batteries are running low within an hour or two. " "The CHARGE light on the base unit does not come on. " Before you first used the handset, you should have left it on the base unit or charger pod for up to 15 hours to charge the batteries fully. You may need to replace the batteries Clean the battery charging contacts with a dry cloth. Check the connections between the base unit and the mains power socket. 26 Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider (the BT engineers on 151, or your cable company). If you still cannot identify the cause of the problem, contact the Binatone Help Line on 0845 345 9677 Calls are charged at Local Call rate. 27 24 25 14 Answering machine Quick Reference (Fusion 2210 only) For detailed information on how to operate the answering machine, see the separate sheet. Shortcut buttons To control answering machine functions, you first press the button (also labelled R). You can then scroll through the menus for the function you want, and press to select it. Alternatively, some of the numbered buttons also give you shortcuts for OK functions you often use. Just press the button followed by the numbered button, as shown here. 15 Guarantee and service The Binatone Fusion 2200/2210 is guaranteed for 12 months from the date of purchase shown on your sales receipt. The Guarantee does not cover damage by misuse or negligence, or by excessive voltages -- for example, faults on the telephone line, or lightning. In the unlikely event that you need to return your Fusion 2200/2210 to our Repair Centre while it is under guarantee, there will be a £5 handling charge. [. . . ] C takes you back to the previous character; takes you to the next one. If you need to insert a pause when keying in a number, press the CDS button. (You'll only need this if you're using your phone on a PBX. ) P To make a repeat call to one of the 10 last numbers you dialled: 1 Press or until the number is shown on the display 2 Press PHONE or SPEAKERPHONE Muting the mouthpiece 6 Press OK OK You can now carry on deleting numbers, or press MENU back to standby mode. To make a memory call again to go 1 Press CDS 2 Press or P to scroll through the records Press C once to mute the mouthpiece While the mouthpiece is muted the person on the other end of the call can't hear you. is shown on the display, and you cannot press any numbered key to send digits down the line. [. . . ]