User manual BINATONE E800

[. . . ] Color profile: Generic CMYK printer profile Composite Default screen 11 Customising your handset Key tone Normally, whenever you press a button on the handset, you hear a `beep' tone. You can turn these tones off if you prefer. Contents of this User Guide 1 2 3 Where to find it Before you start Installation Switching on and off Making and answering calls Last Number Redial Caller Display Memory dialling Intercom, transfer and conference Handset registration Customising your handset Customising your base unit Indirect Network Cleaning and care Connection and conditions for use Technical details Guarantee and service Troubleshooting General points You can customise the settings of your e800 handset and base unit, using a menu which is shown on the handset's display. Please note that: If you don't press any button for about 25 seconds, the handset will time out and the display will return to standby mode. When you confirm any setting you have made, you'll hear a confirmation tone. [. . . ] Now I can't use my handset. " "There is interference and noise on the line. " If you went out of range, move the handset closer to the base unit before you try again to make a call. 1 Press PROG then 2 5 0 2 Key in the line access code (up to four digits) 3 Press PHONE/OK If the fault persists . . . Move the handset closer to the base unit, or to a different position. Try moving the base unit so that it's not near other electrical equipment, such as a television or a computer. You'll get the best results if you site the base unit as high as possible. For example, in a two-storey house, the first-floor landing is an ideal place for the base unit. You need to subscribe to the Caller Display feature from BT or your service provider. Or they may be calling from a network that does not transmit the Caller ID (for example, it may be an international call). "I try to recharge the batteries, but I still get a warning that they are low. " You need to replace the batteries. To find out how to obtain replacements, call the Binatone Spares Department on 0845 345 9677, between 9. 00 am and 5. 00 pm, Monday to Friday. Dispose of used batteries safely -- never burn them, or put them where they could get punctured. DON'T use non-rechargeable batteries in your e800 -- they may burst, causing damage. to confirm Indirect Network "The Caller Display feature isn't working. " "The Indirect Network feature isn't working. " You must subscribe to an alternative network provider before you can use this feature. If you have more than one registered handset, you need to turn the feature on for each one individually, as well as setting the network access code on the base unit. Disconnect all other instruments connected to the same line as the e800 and see whether you can make a call. Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. Contact the service provider (the BT engineers on 151, or your cable company). If you still cannot identify the cause of the problem, contact the Binatone Help Line on 0845 345 9677. E:\Binatone2005\e800_A2\e800_A2_01. vp 10 May 2005 15:47:09 Color profile: Generic CMYK printer profile Composite Default screen 1 Where to find it UP and DOWN buttons Press during a call to adjust the volume in the earpiece. Press to move through the list of stored numbers or Caller Display records. (Last Number Redial)/ CDS/ PAUSE button Press ONCE to make a repeat call to one of the last five numbers you dialled. /INT (Intercom) button Press to make an intercom call (if you have more than one handset). . . . and symbols on the display The time is shown if you've set the handset's clock The handset's number (1 if you have a single system, 1, 2 or 3 if you have a Twin or Triple system) 2 Before you start Unpacking your e800 system In the box are: the cordless handset (up to six, depending on which e800 system you have bought) the base unit three rechargeable batteries and a battery compartment cover for each handset a telephone line cable for the base unit a mains power lead and adapter for the base unit up to five charger pods, each with a separate mains power lead and adapter. Keep the packaging materials in a safe place in case you later need to transport the unit. Positions for the base unit and charger pod The base unit and charger pod should each be placed on a level surface, in a position where: the mains adapter plug will reach an easily accessible 230-V AC switched mains supply socket -- never try to lengthen the mains power cable the telephone line cable will reach your telephone line socket or extension socket (base unit only; charger pods have no connection to the telephone line) it is not close to another telephone -- this can cause radio interference during calls it is not close to a sink, bath or shower, or anywhere else where it might get wet it is not close to other electrical equipment -- fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. To use your handset and base unit together, you must be able to establish a radio link between them. [. . . ] The ringing tune for intercom calls is different from that for outside calls. When someone makes an intercom call to you INT appears on your handset's display, and you can answer and end the call as normal. To shuttle between two calls When you have both an outside call and an intercom call in progress, you can shuttle from one to the other, like this: 10 Handset registration To select a base unit If your handset is registered to more than one base unit, it will automatically select the one with which it can best set up a radio link (usually the nearest one). You don't need this function if you have only one base unit. Press Ø/INT for one second to speak to each in turn, putting the other on hold You can transfer the outside call to the other handset by pressing HANG UP/C while you're connected to the intercom call. If you press HANG UP/C while you're connected to the outside call, you'll disconnect it. The handset(s) supplied with your e800 base unit are already registered -- the first one as handset number 1, the second as number 2. [. . . ]