User manual BINATONE E3300

[. . . ] Important note -- emergency calls The e3300 is not designed for making emergency calls when the mains power fails. So you should make alternative arrangements for access to Emergency Services. (This means that you should also have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure. ) If you need help . . . The Binatone Help Line is available from 9. 00 am to 5. 00 pm, Monday to Friday, on 01325 304 473 Unpacking your e3300 In the box are: I I I I I I the cordless handset (one for a Single system, two/three for a Twin/Triple system) the base unit rechargeable batteries and a battery compartment cover for each handset a telephone line cable for the base unit a mains power lead and adapter for the base unit if you have a Twin or Triple system, one or two charger pods, each with a separate mains power lead and adapter. Keep the packaging materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee. Where to find it HANG UP / C (Cancel) button Press to hang up at the end of a call. [. . . ] If you select 0, your handset will automatically select the base unit that gives the strongest connection. 5 (Optional) Key in a handset number If you don't key in a number at this point, the handset will be registered with the lowest free number. The handset beeps to confirm registration. 3 Press the PHONE button to confirm 20 Binatone Help Line: 01325 304 473 21 Using a multi-handset system Customising your handset To register to a different brand of base unit Your e3300 can be registered to any GAP-compatible base unit; or your can register other GAP-compatible handsets to your e3300 base unit. But we do not guarantee that all features or display messages will be available using other manufacturers' equipment. 1 Follow the instructions in the base unit's User Guide to put the base unit into registration mode (for example, step 1 on page 20). 2 Follow the instructions in the handset's User Guide to register the handset (for example, steps 2 to 5 on page 20). If you need to enter a PIN code for the base unit, refer to the base unit's User Guide. The handset's PIN code The handset has a default PIN (personal identity number) of 0000. You can change it to any four-digit number you'll remember easily. If you leave it at the default, you won't need to key it in to change the handset's settings. 1 Press the PROG button then 1 8 2 Key in your chosen PIN 3 Press the PHONE button to confirm If you forget your PIN, and you want to change the handset's settings, you'll need to reset the handset as described on page 26. Customising -- general points You can customise the settings of your e3300 handset and base unit using a menu which is shown on the handset's display. Please note that: I Auto-answer When a call comes in, you need to press any button to answer it. Or you can set auto-answer -- so, if the handset is in place on the base unit, you simply lift it to answer the call, without pressing any button. If you have set a PIN code for your handset and/or your base unit (see pages 23 and 27), you will need to key it in after you press PROG 1 (handset) or PROG 2 (base unit) to make changes. The instructions in this User Guide assume that you have not set a PIN. If you don't press any button for about 25 seconds, the handset will time out and the display will return to standby mode. When you confirm any setting you have made, you'll hear a confirmation tone. If you make a mistake, you'll hear a warning tone. 1 Press the PROG button then 1 5 2 I Use the L or M button to set: 0 for auto-answer off 1 for auto-answer on Press the PHONE button to confirm 3 I 22 Binatone Help Line: 01325 304 473 23 Customising your handset Customising your handset Ringer volume and melody The handset has eight ringer volume levels, including 0 for off; and eight ringer melodies. With the volume set to 0, the handset will not ring for an incoming call, but the display will show call or the phone number. To change the volume: Direct Call With Direct Call turned on, when you press any key except the PROG button, the handset will automatically make a call to a number you have programmed in. This feature is sometimes called babysitter's call. 1 Press the PROG button then 1 1 1 ! 2 3 Use the L or M button to change the volume Press the PHONE button to confirm With Direct Call turned on, it is not possible to make emergency calls, unless you have programmed an emergency number such as 999 as the Direct Call number. But remember that the number you have programmed will be dialled automatically when any key is pressed. Before you can turn Direct Call on, you must program the telephone number. 1 To change the melody: Press the PROG button then 1 3 1 Press the PROG button then 1 1 2 2 2 3 Key tone Use the L or M button to change the melody Press the PHONE button to confirm Normally, whenever you press a button on the handset, you hear a `beep' tone. You can turn these tones off if you prefer. Key in the number You can press the HANG UP/C button to clear digits one by one; or press and hold the HANG UP/C button to clear the Direct Call number completely. Press the PHONE button to confirm To turn Direct Call on and off: 3 1 Press the PROG button then 1 2 1 Press the PROG button then 1 1 3 2 2 Use the L or M buttons to set: 0 for key tone off 1 for key tone on Press the PHONE button to confirm Use the L or M buttons to set: 0 for Direct Call off 1 for Direct Call on Press the PHONE button to confirm While Direct Call is turned on, the display shows and the Direct Call number. [. . . ] To find out how to obtain a replacement, call the Binatone Spares Department on 01325 304 473, between 9. 00 am and 5. 00 pm, Monday to Friday. Dispose of used batteries safely -- never burn them, or put them where they could get punctured. If your PBX requires you to wait for a second Dial tone before dialling the telephone number, press the LNR/CDS/P button for a pause between the access code and the number. You can also set up your e3300 so that it automatically inserts a 2-second pause after you dial the outside line access code, as follows: 1 Press the PROG button then 2 5 0 2 3 Key in the line access code (up to four digits) Press the PHONE button to confirm PBX use "The Recall You may need to press and hold the R button for a function doesn't couple of seconds, rather than pressing it briefly. seem to work. " "Last Number Redial and/or memory dialling don't work on a PBX. " When you first make a call, press the LNR/CDS/P button for a pause between the outside line access code (e. g. [. . . ]