User manual BINATONE COMBO 2310

[. . . ] USER GUIDE Concept Combo 2310 CORDED AND DIGITAL CORDLESS TELEPHONE WITH ANSWERING MACHINE UK BTP Ver 4, Nov 07 Before operating this set, please read these instructions carefully. For instructions on how to use the cordless part see the "Combo 2310 Cordless Handset" user guide. Important note — emergency calls The CC2310 cordless handset is not designed for making emergency calls when the mains power fails. But, if there’s a power failure, you can use the base unit telephone to make an Emergency Call, by lifting up the corded handset instead of using the speakerphone. Note: After lifting the handset you will need to wait for several seconds to get dial tone, before keying in the telephone number to make the call. [. . . ] If the memory becomes full, the Message Light will flash rapidly, and you will need to delete some messages to create space before any more messages can be recorded. You can switch the answering machine OFF or ON, and when it is ON, select an Answer and Record mode or an Answer Only mode. The Answer and Record mode allows a caller to leave a message, and is set when OGM1 (Out Going Message 1) is selected. The Answer Only mode, does not allow a caller to leave a message, and is set when OGM2 (Out Going Message 2) is selected. The answering machine is supplied with pre-set announcements for OGM1 and OGM2, but you can record your own personal announcements if you wish. When the answering machine is ON it will answer after a set number of rings (default 5), but you can change the number of rings if you wish. When the answering machine is OFF, or if the memory is full, it will answer after 15 rings, which allows remote access if required. Switching TAM on/off 1. If the TAM is turned off, the display will show “TAM OFF” 12:00 TAM OFF 9/08 To Set up a three-way conference Binatone Help Line : 0845 345 9677 25 Press and hold STOP/ON/OFF for over 2 seconds to switch TAM on. Then you can see “OGM 1” on the display and hear the voice prompt “Answer ON, Announcement One”. After this, the display will show the number of messages. 12:00 9/08 00/02 MSGS You can switch between OGM 1 and OGM 2 by pressing STOP/ON/OFF briefly, provided the TAM is already ON. (2) Switch TAM off If the TAM is already switched on, either with OGM 1 or OGM 2. By MENU Alternatively, you can switch the TAM ON or OFF using the Base menu system. Press the UP button to show "TAM", and then the MENU/OK/MUTE button to select it. Press the MENU/OK/MUTE button to show "ON" or "OFF". or Press the UP or DOWN button to choose "ON" or "OFF". If "ON" is selected, the display will then show "OGM1" or "OGM2" or Press the UPor DOWN button to choose "OGM1" or "OGM2", depending on whether you want to set answer and record (OGM1) or answer only (OGM2). Press the MENU/OK/MUTE button to select it, and the display will return to "TAM ON/OFF". Press the PHONEBOOK/BACK button to return to the previous menus. Binatone Help Line : 0845 345 9677 26 To Record your Outgoing Message (OGM) OGM1 is set as the default announcement when you set up the CC2310 for the first time. If you want you can record your own personal announcement of up to 60 seconds for each OGM. By Hotkey (1) To record OGM1 The pre-set announcement for OGM1 is “Sorry we cannot answer your call now, please leave your message after the beep". If you want to record your own OGM 1 message, first ensure OGM1 is set as the outgoing message. Then press and hold REWIND/OGM, you will see “OGM 1” on the display and hear a voice prompt “PLEASE RECORD NEW ANNOUNCEMENT AFTER THE BEEP”. After a beep tone, the display will show “RECORD” and then you can start speaking. [. . . ] Or they may be calling from a network that does not transmit the caller’s number (e. g. it may be an international call. ) Binatone Help Line : 0845 345 9677 40 “When I try to make a call, I hear Busy tone. ” If you’re using a CC2310 multi-handset system, check whether other handsets are already on a call. “The volume in the earpiece is low when I’m on a call” Make sure you’re holding the earpiece correctly over your ear. Adjust the volume using the UP/DOWN button. Intercom and transfer “I can’t transfer a call” Make sure the other handset is in range of the base unit. Make sure you are dialling the correct number for the other handset. If the fault persists… Disconnect all other instruments connected to the same line as the CC2310 and try to make a call Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. [. . . ]