User manual BINATONE AC2000

[. . . ] To end the call, return the Handset to the Base unit cradle. 2 3 4. Lift the Handset and check for Dial tone in the earpiece. Making a call 1 2 3 Receiving a Call 1 2 T elephone operation continue. . . 3. Desk/Wall mount installation installationInstallation Desk mount - Press to select memory location. For normal position, as shown below, place the Base unit on top of a desk on any desired but suitable location. Last Number Redial 1 2 Lift the Handset. The phone automatically dials the last number you called (maximum of 48 digits). [. . . ] Signalling type: DTMF (dual-tone multifrequency) also called tone dialing. ! The AC2000 telephone must be serviced by trained engineers. NEVER attempt any repairs or adjustments yourself - you could make the problem worse and invalidate the Guarantee. you have followed the steps listed in Section 2 to install and set up your AC2000 phone. Everyday use ALWAYS check first that: Speed dialing using the One Touch memory location; 1 2 Lift the Handset. The number dials automatically. Network connection This equipment is intended to be used in the UK only. Operation on other countries' PSTN termination points cannot be guaranteed. Declaration of conformity The AC2000 phone complies with the essential protective requirements and objectives of: EC R&TTE Directive 1999/5/EC EC Low Voltage Directive 2006/95/EC EC EMC Directive 89/336/EEC and conforms to the following relevant harmonized standards: Network: TBR37, TBR38 EMC: EN 55022, EN 55024 Safety: EN 60950 Waste electrical products must not be disposed of with household waste. This equipment should be taken to your local recycling centre for safe treatment. "I cannot make or answer calls. " Make sure you're using the telephone line cable that was supplied with your AC2000 phone. Other telephone line cables might not work. Troubleshooting continue. . . "The phone does not ring" Make sure you're using the telephone line cable that was supplied with your AC2000 phone. Check that the total REN value of all equipment connected to your telephone line is not more than 4. "The phone does not dial" Make sure you're using the telephone line cable that was supplied with your AC2000 phone. Disconnect all other instruments connected to the same line as the AC2000 phone and see whether you can make a call. Disconnect the Base unit from the telephone line and plug a different phone into the master telephone socket. If the call does not work, and you are using a two- way socket adapter, remove it and plug a telephone directly into the socket. Contact the service provider (the BT engineers on 151, or your cable company). If you still cannot identify the cause of the problem, contact the Help Line on 0845 345 9677 Calls are charged at Local Call rate. Speed dialing using the Two Touch memory locations; 1 2 3 Lift the Handset. The display shows 'LoAd-' Press 0~9 for the memory location. The number dials automatically. T elephone operation continue. . . Memory Check 1 2 3 To check the number stored in a memory location. Press the memory location button (M1, 0~9). Help Line - 0845 345 9677 Calls are charged at Local Call rate. Connection and conditions for use You can connect your AC2000 phone to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc. ) connected to an exchange line must not add up to more than 4 - otherwise, one or more of them may not ring and/or answer calls correctly. [. . . ] Operational notes Electrical safety DON'T let the Base unit get wet. Electrical equipment can cause serious injury if used while you are wet or standing in water. If the Base unit ever falls into water, DON'T retrieve it until you have unplugged the power lead from the mains and the telephone line plug from the telephone socket; then pull it out by the unplugged cables. NEVER use your classic wooden phone outdoors during a thunderstorm - unplug the Base unit from the telephone line when there are storms in your area. [. . . ]