User manual BINATONE 921A

[. . . ] Also you cannot dial numbers from memories when the mains power is off. *** Before operating this set, please read these instructions carefully. If you need help . . . . . Binatone Helpline (for UK only) Monday to Friday from 9:00am to 5:00pm Tel: 0845 345 9677 **Please note that all calls are charged at local rate Or visit our website: http://www. binatoneonline. com Unpacking your CC2310 system In the box, you will find: the base unit telephone a telephone line cable for the base unit a mains power adapter for the base unit the cordless handset (up to five, depending on which CC2310 system you've bought) two 1. 2V 550mA rechargeable batteries and a battery compartment cover for each handset up to five charger pods, each with a mains power supply for multi handset systems two user guides, one for the corded phone and one for the cordless handset. Keep the packaging materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee. Where to find it Delete (DEL) Press to delete messages, memos, stored numbers or Caller Display records. Up-Down(CDS) LCD Display Intercom Press to make an intercom call or to transfer a call Press to access the Caller display records and scroll through them Press to change earpiece speakerphone volume Press to scroll through the lists the lists and menu options Message Light Turns ON when the TAM is ON. [. . . ] Press the MENU/OK button to see "BASE 1" If the handset already has a registration to a base there is a "+" on the right side of the display, and you should choose another base number if you don't want to lose that one. Binatone Help Line : 0845 345 9677 23 4. Press the MENU/OK button to see "PIN ?" (key in 4 digits pin code -- 0000) 6. Press the MENU/OK button to confirm, and the display will flash "SEARCHING 1" (or 2, 3, 4) 7. At the same time, on the base, press the MENU/OK button to see "PHONEBOOK" 8. Press the MENU/OK button to see "SEARCHING" flash on base display After a short delay, if the registration is successful, there will be a confirmation beep, and the Handset display will go back to idle mode with the new handset number a three-way conference shown (e. g. The base display will also go back to idle mode. To de-register a handset You may need to do this if you need to replace a faulty handset. Call the Binatone help line if you need more advice. To de-register a handset using the CC2310 base menu With the base in idle mode: 1. Press the MENU/OK button to see "PHONEBOOK" 2 . Press the DOWN button twice to see "SETTINGS" 3. Press the MENU/OK button to see " HS 1 " (or 2, 3, 4) Press the UP or DOWN button to select the handset you want to de-register. Press the MENU/OK button to confirm, and the selected handset will be de-registered. (The display on the handset that has been deleted will show "UNREGISTERED". ) /C Press * at any the PHONEBOOK/BACK button to return to the previous menu time. Then press and hold REWIND/OGM, you will see "OGM 1" on the display and hear a voice prompt "PLEASE RECORD NEW ANNOUNCEMENT AFTER THE BEEP". After a beep tone, the display will show "RECORD" and then you can start speaking. Then the unit will playback the OGM 1 announcement automatically. (2) To Record OGM 2 The pre-set announcement for OGM2 is "Sorry I cannot answer your call now, please call later" . The unit will automatically switch to OGM 2 to answer a call when the memory is full. If you want to record your own OGM2 message, first ensure OGM2 is set as the outgoing message. Repeat above sequence as OGM 1 to record the OGM 2 announcement. 2. By MENU Alternatively, you can record OGM1 or OGM2 using the Base menu system. Press the UP button to show "TAM", and then the MENU/OK/MUTE button to select it. Binatone Help Line : 0845 345 9677 27 Press the UP button to show "TAM SETTINGS". Press the MENU/OK/MUTE button to show "OGM1" or Press the UP or DOWN button to choose "OGM1" or "OGM2" Press the MENU/OK/MUTE button to select it and show "PLAY". Press the MENU/OK/MUTE button to hear a voice prompt "PLEASE RECORD NEW ANNOUNCEMENT AFTER THE BEEP". Then the unit will playback the OGM announcement automatically. To playback the OGM 1. [. . . ] If a cordless handset is already using the line, you need to wait until it's finished its call. "The phone does not ring" Check that the base unit's mains power adapter is plugged in and power is switched on. The base unit needs mains power for normal operation of the phone ­ only the basic handset calling works without mains power. Make sure you are using the telephone line cable that wa supplied with your CC2310. Other telephone line cables might not work "The Caller Display feature isn't working" You need to subscribe to the Caller Display feature from your network service provider. You should find contact details on your phone bill. The caller may have withheld their number by dialling 141. [. . . ]