User manual BIAMP MAXXAM 8 8 M2-V

[. . . ] Connect other end of power cord to power entrance located on the rear of Audia unit. Under normal conditions, all LED's will remain green once power-up sequence has completed. 5. Assign IP address to PC PC must have a unique IP address before it can communicate with an Audia device. Right Click My Network>Properties>Local Area Connection>Right Click Properties>TCP/IP>Properties IP address should be 192. 168. 1. x (x=1-254) Subnet mask should be 255. 255. 255. 0 Click Ok when complete Close My Network 6. [. . . ] Right Click My Network>Properties>Local Area Connection>Right Click Properties>TCP/IP>Properties IP address should be 192. 168. 1. x (x=1-254) Subnet mask should be 255. 255. 255. 0 Click Ok when complete Close My Network 6. Connect PC to network Attach a "straight-through" Ethernet cable from PC 10/100baseT network card to a 10/100baseT Ethernet switch. "Straight-through" Ethernet cables connect transmit pins directly to receive pins (pin 1 to pin 1, pin 2 to pin2, pin 3 to pin3, etc. ). You can easily determine if an Ethernet cable is "straight-through" by looking at the conductors on the RJ-45 connectors. If the wiring is identical on both ends, it is a "straight through" Ethernet cable. 7. Connect Audia device to network Connect one Audia device to network using "straight through" Ethernet cable attached from the rear panel Ethernet jack to the 10/100baseT Ethernet switch. 8. Connect to network with Audia software Open Audia software then connect to network. Assign IP address to Audia device All Audia units ship from the factory with an assigned IP address of 192. 168. 1. 101. When using more than one device in a system, each device must have a unique IP address. Audia device IP addresses must be different from any PC IP address that will be used in this system. Enter appropriate Audia unit serial to equipment table Tools>Equipment table>Select desired Audia unit Select OK when complete 10. Send Configuration File>Network>Send System Configuration Sends layout configuration to selected Audia unit. 11. Start Audio 12. Adjust component parameters as needed Optional: 13. Disconnect PC from Audia system File>Network>Disconnect from Audia system 14. Disconnect PC from Network File>Network>Disconnect from network WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, and normal wear and tear of items such as paint, knobs, handles, and covers are not covered under this warranty. 5. BIAMP SYSTEMS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. [. . . ] Electro-mechanical fans, electrolytic capacitors, and normal wear and tear of items such as paint, knobs, handles, and covers are not covered under this warranty. 5. BIAMP SYSTEMS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. No agent, employee, distributor or dealer of Biamp Systems is authorized to modify this warranty or to make additional warranties on behalf of Biamp Systems. [. . . ]