User manual BIAMP EQ 210

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN. CAUTION: Opening the unit enclosure will place operator at risk of injury due to electric shock. 1 FRONT PANEL FEATURES channels 1 aux 2 aux 3 aux 4 aux 5 aux 6 aux 7 aux 8 aux +15 C UL R power US LISTED 52SJ 120V 60Hz 900 Watts ~ main equalizer +15 max min max min max min max min max min max min max min max min main main main main main main main main -15 -15 63 min max min max min max min max min max min max min max min max 125 250 500 1k 2k 4k 8k 16k high high high high high high high high IWA 250 Powered Mixer -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 HPF OFF ON AUTO MANUAL OVERRIDE low low low low low low low low aux -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 -12 +12 min max gain gain gain gain gain gain L / R Sum OFF OFF ON ON 20dB Pad OFF OFF 20dB Pad L / R Sum ON ON main aux out main out line mic line mic line mic line mic line mic line mic min max min max min max peak peak peak peak peak peak peak peak active peak S LR LR common main EQ in main out 1 2 3 4 inputs 5 6 7 8 override input aux out main out Phantom Power Aux: These screw-driver controls set the level of channel signals sent to the Aux Out master control. Aux controls are used to create an independent mix of channel signals for a secondary sound system. [. . . ] Peak: These red LEDs will light whenever channel signal levels reach +10dB (8dB below clipping). Use this feature to aid in proper adjustment of Gain and 20dB Pad (see above). Phantom Power: These DIP switches assign +48 Volt DC to the respective inputs for powering condenser microphones. Phantom Power should remain off when input is from line-level sources or dynamic microphones. Always turn AC power off, or turn all level controls down, before switching Phantom Power. FRONT PANEL FEATURES Inputs (Channels 1~6): These plug-in barrier strips provide mic/line input to Channels 1~6. These inputs accept signals from balanced low-impedance microphones or from balanced (or unbalanced) line-level sources. Balanced input (Mic or Line) is wired high to (+), low to (-), and ground to ( ). Unbalanced Line input is wired high to (+), and ground to both (-) and ( ). Phantom Power (+48V) is selectable per input (see above) and remote level control is optional. Inputs (Channels 7 & 8): These plug-in barrier strips provide line level input to Channels 7 & 8. These inputs accept mono (balanced or unbalanced) or stereo (unbalanced) signals from line-level sources (see L/R Sum above). The Aux Out connector is a plug-in barrier strip, which provides a balanced line-level output for feeding external equipment (recorders, auxiliary amplifiers, etc. ). For unbalanced output, wire high to (+) and ground to ( ), leaving () un-connected. HPF: This DIP switch enables a high-pass filter (12dB/octave @ 125Hz) which reduces unnecessary low-frequency signals. Enable HPF whenever the 70V or 25V outputs are being used, or in any 'speech only' applications. Override: This DIP switch determines whether the Override Input will trigger muting of all other input signals automatically (via signal presence) or manually (via external switch). Main Equalizer: This 9-band graphic equalizer adjusts the frequency response (tonal balance) of signals sent to the Main Amplifier. Each control provides ±15dB boost/cut at the designated center frequency. From the factory, the Main Equalizer receives signal from the mixer Main Out. However, the Main Equalizer may instead be wired to receive signal from another source (see Main Out above). Do not boost frequencies below 250Hz whenever the 70V or 25V outputs are being used. Caution: complete all connections & installation before turning power on. [. . . ] If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. [. . . ]