User manual BIAMP DMD

[. . . ] If the combined current requirement of the multiple modules exceeds the current capability of the power source, then additional power supplies may be needed. The optional 12V power supply has a typical current capability of 165 mA. (4) Out: These three screw terminals provide an electronically balanced, cross-coupled output from the channel. The screw terminals are provided on a plug-in barrier strip, which allows pre-wiring of cables before installation. [. . . ] If only 2-conductor TS 1/4" Phone cables are available, an In/Out jack may be used as the input, while the associated Patch jack is used as the output. 2 JUMPER OPTIONS To access internal jumper options: A) remove any power connections to the module; B) place the module on a flat surface with the top panel facing up and the front panel facing away; C) remove all screws from the top panel; D) remove the top panel. Microphone Level Output: From the factory, the Out terminals for each channel provide line-level signal. Internal jumpers allow each output to be independently attenuated (-60dB) for microphone-level applications. This attenuation of output signal level only occurs at the Out terminals for each channel (In terminals, In/Out jacks, and Patch jacks operate strictly at line-level). Any or all of Channels 1~4 may be assigned output attenuation by moving jumpers J101~J401 forward one pin (J101 is for Channel 1, J201 is for Channel 2, J301 is for Channel 3, and J401 is for Channel 4). Channel 2 Summing: From the factory, the Out terminals for each channel provide only the signal which appears at the input to that channel. An internal jumper allows input signal from Channel 1 to be assigned to Channel 2 Out. Channel 2 Out will then provide a combination of both Channel 1 & Channel 2 input signals, while Channels 1, 3, & 4 will continue to maintain their individual output capabilities. NOTE: Channel 1 signal which has been assigned to Channel 2 Out will not appear at Channel 2 Patch. Channel 1 may be assigned to Channel 2 Out by moving jumper J103 left one pin. Channel 4 Summing: From the factory, the Out terminals for each channel provide only the signal which appears at the input to that channel. Internal jumpers allow input signals from Channels 1~3 to be individually assigned to Channel 4 Out. Channel 4 Out will then provide a combination of all the input signals which have been assigned to it, while Channels 1~3 will continue to maintain their individual output capabilities. NOTE: Channel 1~3 signals which have been assigned to Channel 4 Out will not appear at Channel 4 Patch. Any or all of Channels 1~3 may be assigned to Channel 4 Out by moving jumpers J102~302 left one pin (J102 is for Channel 1, J202 is for Channel 2, and J302 is for Channel 3). See diagram below. CH4 SUM CH1 CH2 J102 J202 J302 CH2 SUM CH1 J103 front panel CH3 DMD Circuit Board -60dB J401 -60dB J301 -60dB J201 -60dB J101 rear panel 3 APPLICATIONS Bar Sound System with Remote Equipment Rack COMPACT 1 DIGITAL AUDIO 2:50 101. 9 FM CD player AM/FM tuner DMD BIAMP SYSTEMS Portland, Oregon an affiliate of Rauland-Borg Corp. out ±12VDC 15W Class 2 wiring in out in out in out in patch MADE IN U. S. A. in/out 3 patch in/out 2 patch in/out 1 patch in/out DC out DC in 4 DMD BIAMP SYSTEMS Portland, Oregon an affiliate of Rauland-Borg Corp. out ±12VDC 15W Class 2 wiring in out in out in out in patch MADE IN U. S. A. in/out 3 patch in/out 2 patch in/out 1 patch in/out DC out DC in 4 infrared remote control ADVANTAGE SPM412 VOL VOL MUTE 1 CHANNEL SELECT 2 3 InfraRed Receiver to stereo sound system SPM412 GI NR D2 I R 3 paging mic This application shows two stereo music sources and a paging microphone, which are located at the bar for easy access. The remainder ® of the sound system (an ADVANTAGE SPM412, equalizers, & amplifiers) is installed in a remote equipment rack to prevent tampering. Source selection, volume adjustments, and paging-over-music are accomplished via remote control of the SPM412. The outputs from the ® music sources and the inputs to the SPM412 are unbalanced. Therefore, an ADVANTAGE DMD module is used (at the bar) to balance the music sources before they are sent to the remote equipment rack. A second DMD module (at the rack) accepts the balanced music signals from the first DMD, and provides the unbalanced outputs necessary for connection to the SPM412. 4 MAIN LEVEL 4 R L limit threshold mono signal present level level level level R L L R mic trim phtm power on USE ONLY WITH 250V FUSE 110 220 remote zone out main out main stereo/mono min max limit 0 4 10 0 3 10 0 2 10 0 1 10 4 min 3 2 inputs 1 +10 max mute mic input APPLICATIONS Church Sound System with Choir Monitor Mixer ONE +48VDC 4W Class 2 E17934 DC out main out main stack main patch ±12VDC 15W Class 2 pad patch in pad patch in pad patch in pad patch in pad patch in pad patch in pad patch in pad patch in 8 7 6 5 4 3 2 1 to choir monitor sound system DMD BIAMP SYSTEMS Portland, Oregon an affiliate of Rauland-Borg Corp. out ±12VDC 15W Class 2 wiring in out in out in out in patch MADE IN U. S. A. in/out 3 patch in/out 2 patch in/out 1 patch in/out DC out DC in 4 DMD BIAMP SYSTEMS Portland, Oregon an affiliate of Rauland-Borg Corp. out ±12VDC 15W Class 2 wiring in out in out in out in patch MADE IN U. S. A. in/out 3 patch in/out 2 patch in/out 1 patch in/out DC out DC in 4 to main house sound system CASCADE 8/332r mic speech & choir mics plus music playback 8 mic 7 mic 6 mic 5 mic 4 mic 3 mic 2 mic 1 mic line line line line line line line line line patch patch patch patch patch patch patch patch patch send 1 8 L return 1 L R R return 2 send 2 L main output (balanced) R monitor/send 3 output tape outputs 7 6 5 4 3 2 1 CASCADE Series model 8/332r mono output external 48V phantom power supply 115/230 VAC 50/60 Hz 120 Watts max This application shows a BIAMP Cascade 8/332r mixer accepting inputs from speech and choir microphones, as well as a tape deck for music playback. The Cascade mixer is installed at the rear of the church, and is used to mix for the main house sound system. [. . . ] BIAMP SYSTEMS SHALL NOT IN ANY EVENT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS, LOSS OF USE, PROPERTY DAMAGE, INJURY TO GOODWILL, OR OTHER ECONOMIC LOSS OF ANY SORT. EXCEPT AS EXPRESSLY PROVIDED HEREIN, BIAMP SYSTEMS DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSONS ARISING OUT OF USE OR PERFORMANCE OF THE PRODUCT, INCLUDING LIABILITY FOR NEGLIGENCE OR STRICT LIABILITY IN TORT. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. BIAMP SYSTEMS EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. [. . . ]