User manual BIAMP DJ 3600, 3500, 3001

[. . . ] When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Use only attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Connections to these teminals must be made by qualified personnel. 2 3 4 5 FRONT PANEL On Indicator: This green LED remains lit when AC power is applied to the unit. [. . . ] Temp / Fault Indicator: This red LED indicates over-temperature and output fault conditions for the amplifier. When the LED remains lit, the amplifier has an over-temperature condition. When the LED is flashing, the amplifier has an output fault condition. Either condition will temporarily de-activate the amplifier, causing the Signal / Peak LED to turn off as well. The amplifier will attempt to self-reset once the over-temperature or output fault condition is resolved. CAUTION: The DJ 3600, 3500, 3001 is cooled by a variable speed fan, which exhausts warm air from the left side panel. To allow proper ventilation, an un-obstructed clearance of at least 0. 75" must be maintained along the left side panel of the DJ 3600, 3500, 3001. 6 REAR PANEL C UL R WARNING: SHOCK HAZARD - DO NOT OPEN US LISTED 52SJ NO USER SERVICEABLE PARTS INSIDE. TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DJ 3600, 3500, 3001 Class 2 Wiring xfmr output direct output BIAMP SYSTEMS Designed in Oregon, U. S. A. Assembled in India AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR E215636 CAUTION I CAUTION: Risk of fire replace fuse only with same type T 6. 3 A L 250 V RISK OF ELECTRICAL SHOCK. DO NOT OPEN. Use only with a 250V fuse Employer uniquement avec un fusible de 250V signal / peak temp / fault UNBAL 775mV OFF level O BAL 300mV HPF ~120V 60Hz 900 Watts 8 70V 25V 25V CT COM OUT XFMR INPUT 4 GND input Input: This plug-in barrier strip provides the line-level input to the amplifier. NOTE: The UNBAL / BAL switch must be in the appropriate position (see below). Output: These screw terminals provide the speaker outputs from the amplifier. From the factory, a jumper wire is installed from the 4 terminal (direct output) to the XFMR INPUT terminal. For transformer (xfmr) output, connect speaker negative to the COM OUT terminal, and connect speaker positive to the appropriate transformer output terminal (8 for an 8 ohm speaker load; 70V for a 70 Volt distributed speaker system; 25V for a 25 Volt distributed speaker system). For 'balanced' 25V speaker systems, connections are the same as above, plus a ground connection (center-tap) made to the 25V CT terminal. For direct output from the amplifier, first remove the factory installed jumper wire, then connect speaker negative to the GND terminal, and connect speaker positive to the 4 terminal. AC Fuse & Power Cord: Replace Fuse with same type and value only (6. 3 A 250 V). NOTE: If the Fuse continues to blow, the amplifier may require service. The AC Power Cord is for connection to three-prong grounded AC outlets. CAUTION: Do not remove or defeat the ground prong on the AC Power Cord, as this constitutes a shock hazard. 7 SPECIFICATIONS Continuous Power (4 ohm direct & transformer outputs): Signal-to-Noise Ratio (20Hz~20kHz): referenced to 250 watts into 4 ohm direct output Total Harmonic Distortion: 20Hz~20kHz @ 250 watts into 4 ohm direct output 100Hz~15kHz @ 250 watts at transformer outputs Intermodulation Distortion (SMPTE): Frequency Response (20Hz~20kHz): Input Impedance: balanced unbalanced Input Sensitivity (selectable): Power Requirements: Power Consumption: Dimensions (H x W x D): Weight: 250 watts > 90dB < 0. 2% < 1. 0% < 0. 35% +0/-1dB 20k ohms 10k ohms 775mV / 300mV 120VAC @ 60Hz 900 watts 3. 5" x 19" x 8. 5" (89 x 483 x 216mm) 23 lbs. (10. 5kg) 8 WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. [. . . ] As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. [. . . ]