User manual BIAMP COLUMBIA SERIES

[. . . ] If a control item includes a volume control assignment, the bottom of the display will show a graphical representation of a volume bar with the current level indicated to the right (percentage of maximum level). Capacitive-touch Scroll Wheel The capacitive-touch sensor provides a sleek interface for menu navigation and selection. The glossy-finish finger groove allows for scrolling through and selecting available control items, as well as adjusting volume. 4 COLUMBIA SERIES bAck pANEl Connectors Two Ethernet connectors--one rear-facing RJ45 and one top-facing insulation displacement connector (IDC)--are provided for connecting to the network. The RJ45 and IDC utilize unshielded twisted pair (UTP) wiring to connect to an Audia or Nexia system. [. . . ] The COLUMBIA SERIES is powered using IEEE 802. 3-2008 Power over Ethernet protocol as Class 1 devices. Either a PoE-capable network switch or a PoE injector is required to power the device; there are no other provisions for power inlet. COLUMBIA SERIES Ethernet switch with PoE COLUMBIA SERIES Ethernet switch without PoE PoE injector AC Power 5 COLUMBIA SERIES sEt Up Device Setup Mode The COLUMBIA SERIES can be configured without connecting to a functional Audia or Nexia network. To enter setup mode, connect the COLUMBIA SERIES to a PoE source and place the jumper or any metal object across the locksmith pins. When configuration is complete, remove the jumper and attach it to only one pin to resume normal operation. Please note: many of the configuration settings can be accessed via the Audia or Nexia software. Locksmith: Bridge jumper pins to enter setup mode The cursor has two modes: select and modify. When scrolling through the available items in the list, the gray box will highlight the current selection. "Select" mode in device setup menu On fields that can be modified, use the Select button to transition to and from modify mode. Use the scroll wheel to adjust the setting up or down. "Modify" mode in device setup menu Some screens have additional buttons that are used to accept (OK), reset, or cancel changed settings. Use the scroll wheel to navigate the cursor to these buttons and press the Select button. The Cancel button exits the screen without saving the setting. 6 COLUMBIA SERIES sEt Up Edit Device ID To name the unit, scroll to the ID Tag icon and press the Select button. Use the scroll wheel and Select button to choose the desired characters. The Device ID must match that of a corresponding block in the Audia or Nexia design. (100m) Ethernet cable length can be extended with standard PoE network technology 128 24 Standard Ethernet network wiring Each control configured for specific operation by the system design software EU Directive 2002/95/EC, RoHS Directive CE marked FCC SPECIFICATIONS (COLUMBIA SERIESF) Dimensions Power consumption Control cable requirements Control cable length Control wiring topology Control programming Compliance 6. 22"H x 5. 82"W x 0. 5"D (158mm x 148mm x 12. 7mm) PoE Class 1 (3. 2W @ full display utilization) CAT-5/6/7 Ethernet cable using either RJ-45 or IDC connector 330' (100m) Ethernet cable length can be extended with standard PoE network technology Standard Ethernet network wiring Each control configured for specific operation by the system design software EU RoHS Directive 2002/95/EC; CE; FCC 13 COLUMBIA SERIES wARRANty BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1. BIAMP Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BIAMP Systems dealer, subject to the terms and conditions set forth below. 2 If you notify BIAMP during the warranty period that a BIAMP Systems product fails to comply with the warranty, BIAMP Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BIAMP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BIAMP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BIAMP Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. This warranty is in lieu of all other warranties, expressed or implied. BIAMP Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. [. . . ] The remedies set forth herein shall be the purchaser's sole and exclusive remedies with respect to any defective product. No agent, employee, distributor or dealer of BIAMP Systems is authorized to modify this warranty or to make additional warranties on behalf of BIAMP Systems. Statements, representations or warranties made by any dealer do not constitute warranties by BIAMP Systems. BIAMP Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person. [. . . ]