User manual BIAMP ADVANTAGE SCM 7500 S

[. . . ] Flashing green: The unit is receiving power but not data, or the unit has not been configured correctly. Power supply and network traffic are functional. 5 TTS-1 rear panel O LAN1: Control LAN2: CobranetTM LAN3: Spare LAN4: Spare MSB LSB Device ID BIAMP SYSTEMS Model TTS-1 RS232 port AC power Entrance (iEC) USB ports LAN-1 LAN-3 Device iD (control) (Spare) LAN-2 LAN-4 (CobraNet) (Spare) Device ID The rotary iD switches are located on the back of the TTS-1 and give the unit a unique Device iD. All TTS-1 units must have a unique Device iD to function properly within a Vocia paging World (i. e. , it is not possible to have two TTS-1 units with the same Device iD of hex 07). To assign a Device iD of hex 07, turn the LSB switch to 7 and leave the mSB switch on 0. [. . . ] To create an iD of hex B7, turn the LSB switch to 7 and turn the mSB switch to B. Device iD switches should be set using a 0. 1 inch (2. 5mm) to 0. 12 inch (3. 0mm) flat blade screwdriver. More information on setting IDs and the hexadecimal numbering scheme used in Vocia can be found in the Vocia Help File. Please note: Changes made to the Device iD while connected to the network require a power cycle in order to take effect. Network Connection The TTS-1 has four RJ45 Ethernet connectors located on the rear panel (Control, Vocia Network, and Spare). Each connector has two green LEDs, which display Ethernet Link (left LED) and Activity (right LED). LAN-1 Connector (Control) This port connects the TTS-1 to a control network. This should be separate to the LAN that is being used by the CobraNet port either physically or through the use of managed switches and VLANs. The TTS-1 can be configured in the Vocia software interface via this port, and as such it should be connected to the same network as the configuration PC during set up. LAN-2 Connector (CobraNet) This port is used to communicate with local Vocia devices and as such should be connected to the same network as the local Vocia system. Ensure that air can circulate freely behind, beside, and above the unit. Do not exceed the maximum ambient operating temperature of 113 degrees F (45°C). Be aware of conditions in an enclosed rack that may cause the temperature to exceed ambient room conditions. 585. 0270. 90A 8 TTS-1 SpecificaTiOnS Text-to-Speech Server 1 SPECIFICATIONS Connection: RJ45 with shielded Ethernet/PoE cable (Cat5, Cat5e, Cat6 , or Cat7) Weight: 12 lb (5. 4 kg) Power Consumption (100­240VaC 50/60Hz): Dimensions: Height: Width: Depth: < 350 watts ambient Operating temperature Range: Compliance: 32-113 degrees F (0-45 degrees C) EU Directive 2002/95/EC, RoHS directive CE marked 0. 75 inches (44. 5 mm) 19 inches (483 mm) 17. 5 inches (444 mm) Text-to-Speech Server 1 Block Diagram RS-232 USB VGA LED ID Switches Storage Drive Host Processor Control CobraNet® 9 TTS-1 warranTy BiAmp SYSTEmS iS pLEASED TO EXTEND THE FOLLOWiNG 5-YEAR LimiTED WARRANTY TO THE ORiGiNAL pURCHASER OF THE pROFESSiONAL SOUND EQUipmENT DESCRiBED iN THiS mANUAL 1. BiAmp Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase from an authorized BiAmp Systems dealer, subject to the terms and conditions set forth below. 2 if you notify BiAmp during the warranty period that a BiAmp Systems product fails to comply with the warranty, BiAmp Systems will repair or replace, at BIAMP Systems' option, the nonconforming product. As a condition to receiving the benefits of this warranty, you must provide BiAmp Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BiAmp Systems dealer. Transportation and insurance charges to and from the BiAmp Systems factory for warranty service shall be your responsibility. This warranty will be VOiD if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BiAmp Systems to make repairs; or installed in any manner that does not comply with BiAmp Systems' recommendations. [. . . ] This warranty will be VOiD if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BiAmp Systems to make repairs; or installed in any manner that does not comply with BiAmp Systems' recommendations. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. This warranty is in lieu of all other warranties, expressed or implied. BiAmp Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. [. . . ]