User manual BIAMP ADVANTAGE SCM 7500

[. . . ] Display Both the WS-4 and WS-10 feature a backlit display that provides the user with an easy-to-read interface to view paging information. Microphone The WS-4 and WS-10 are equipped with a handheld noise-canceling microphone. The frequency response and pickup pattern have been tailored for clear speech reproduction and cancelation of ambient noise. This microphone must be used at very close proximity, rather than at a distance as is common with most other microphone types. [. . . ] Device ID switches should be set using a 0. 1 inch (2. 5mm) to 0. 12 inch (3. 0mm) flat blade screwdriver. More information on setting IDs and the hexadecimal numbering scheme used in Vocia can be found in the Vocia Help File. Please note: Changes made to the Device ID while connected to the network require a power cycle in order to take effect. All CobraNet routing and bundle assignments are processed by the Vocia devices locally. Network Connection The WS-4 and WS-10 have two RJ45 connectors located on the back of the unit which are labeled (1) Audio Network and (2) Option. The Audio Network connector should be wired using shielded CAT5, CAT5e, CAT6 or CAT7 cable cabling to interface the WS-4 or WS-10 to a Vocia system via a PoE-compliant network switch. The RJ45 connector provides two LEDs that indicate Ethernet link and network activity (see table below). Left LED None Green Green Flashing green Flashing amber Right LED None None Flashing amber Flashing amber Flashing amber Description No power or data connectivity. Link established and CobraNet activity detected; the unit is acting as a CobraNet performer. Link established and CobraNet activity detected; the unit is operating as a CobraNet conductor. Check cabling and configuration for errors. 5 S-4/WS-10 rEar ViEW This connection carries control data, power and digital audio over CobraNet. PoE-enabled network switches or PoE midspan adapters must be used to power the WS-4 or WS-10. When the zone(s) are ready to receive the announcement, the message will be played and the WS-4 or WS-10 will return to the Destination idle state. Cancel Request?: This status message indicates that the selected Page Code is a Delayed Release page. Once the PTT button is released, the "Cancel" prompt will flash on the display. The "Cancel Request?" message is displayed for five seconds. If the user presses the Cancel button within this five-second period, the recorded page will be discarded and the system will return to idle status. If five seconds elapses and the user does not press the Cancel button, the message will be released for playback as soon as all destination zones are available. Page Will End in "x" Secs: This status message is displayed when a page termination is imminent (either due to lack of memory or a timeout). (EWS-4 Only) Fault: This status message indicates that a General Fault has been detected in the system. (EWS-4 Only) Alarm: This status message indicates that the system is in Alarm mode. Device Information To access the device information, such as Device ID, the system time, and the time and date of the last firmware update, please press and hold down any combination of three of the ten Page Code buttons. Device iD Time/date of last Firmware update System Time 8 135. 50 241. 50 83. 50 0 11. 555 293. 50 S-4/WS-10 inStallatiOn Any combination of the screw holes shown in the rear-view diagram can be used to mount the bracket to the wall (do not fit a screw 5 to the hole marked No Screw). Please note: the maximum screw head height is 0. 157 inch 0 (4mm) (dimension from top of installed screw head to inside of mounting bracket). [. . . ] As a condition to receiving the benefits of this warranty, you must provide BiAmP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BiAmP Systems dealer. Transportation and insurance charges to and from the BiAmP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BiAmP Systems' recommendations. [. . . ]