User manual BIAMP 29QPM QUALITY POWERED MIXERS

[. . . ] Correct operation of the microphone is essential for good speech intelligibility. The recommended distance between the user's mouth and the microphone is between 2 and 4 inches (50 and 100mm). Closer use may cause distortion and unwanted bass boost, while more distant use may result in inadequate sound level. Soft Key Buttons Two soft key buttons are located to the right of the display. [. . . ] The left amber LED "Wait" indicator illuminates while the system establishes audio paths, checks for zone availability, and plays the chime (if selected). The right green LED "Please Talk Now" indicator illuminates once the DS-4 or DS-10 audio path is live. 4 DS-4/DS-10 bOttOM View Device ID The rotary ID switches are located on the bottom of the DS-4 and DS-10 and give the unit a unique Device ID. All desk station units must have a unique Device ID to function within a Vocia Paging World (i. e. , it is not possible to have two desk station units with the same Device ID of hex 07). To assign a Device ID of hex 07, turn the LSB switch to 7 and leave the MSB switch on 0. To create an ID of hex B7, turn the LSB switch to 7 and turn the MSB switch to B. Device ID switches should be set using a 0. 1 inch (2. 5mm) to 0. 12 inch (3. 0mm) flat blade screwdriver. More information on setting IDs and the hexadecimal numbering scheme used in Vocia can be found in the Vocia Help File. Please note: Changes made to the Device ID while connected to the network require a power cycle in order to take effect. All CobraNet routing and bundle assignments are processed by the Vocia devices locally. Network Connection The DS-4 and DS-10 have two RJ45 connectors located on the bottom of the unit that are labeled (1) Audio Network and (2) Option. The Audio Network connector should be wired to shielded CAT5, CAT5e, CAT6 or CAT7 cable cabling to interface the DS-4 or DS-10 to a Vocia system via a PoE-compliant network switch. The RJ45 connector provides two LEDs that indicate Ethernet link and network activity (see table below). If the entered PIN is correct, the station will unlock and be ready for use. After a period of inactivity (no pages made and no buttons pressed), both the DS-4 and DS-10 will revert back to a locked state. This length of time (at a default of 180 seconds) is set using the Vocia software. To lock the station instantly, the user can press and hold down the "Next" and "Previous" buttons at the same time. 6 DS-4/DS-10 DiSplay Display Status Messages The following messages are used to display the state of the DS-4 or DS-10 during normal operation. more information on display status messages can be found in the Vocia Help File. Destination Idle: This status message indicates that the paging station is ready and there are no busy zones among the destinations selected by the Page Code. No Network: This status message indicates that the DS-4 or DS-10 is not connected to a functioning network. Destination Busy: This status message signifies that at least one of the destination zones is busy with a lower priority page. When paging into a busy zone, the lower priority message will be lost. Destination Delay: This status message indicates that at least one of the destination zones is busy with a page of equal priority. [. . . ] As a condition to receiving the benefits of this warranty, you must provide BiAmP Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from an authorized BIAMP Systems dealer. Transportation and insurance charges to and from the BiAmP Systems factory for warranty service shall be your responsibility. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any person not authorized by BIAMP Systems to make repairs; or installed in any manner that does not comply with BiAmP Systems' recommendations. [. . . ]