User manual BESTOP SUPERTOP

[. . . ] Loosely install them with 5/16-18 x 1" Screws, 5/16-18 Tapping Plates and 5/16 Washers. 5/16 5/16-18 x Bow Mount Bracket 1" Screw Washer 5/16-18 x 1" Screw 5/16 Washer Bow Mount Bracket 5/16-18 Tapping Plate Rev. 4 Supertop® with Tinted Windows ­ Installation Instructions Assemble Upper Door Rails Attach each Sunrider Latch Assembly to the rearward set of holes on top of the Rear Upper Rails with two (2) #8 x 1/2" Tapping Screws each. Connect the Rear Rails to the Front Rails Using the Right and Left Rail Connectors and four #8 x 1/2" Tapping Screws per side. Rear Upper Rail #8 x 1/2" Tapping Screws Front Upper Rail Install Door Rail Assemblies Orient the Door Rail Assemblies on the vehicle with the Rail Brackets on top of the side sport bar and the C-Pillar Rails in front of the C-Pillar Base Brackets. [. . . ] Lay the Header Retainer on the Header and position it so the fabric welt is captured between the Header and the Retainer. Line up the holes and attach the Retainer to the Header with eighteen (18) #8 x 1/2" Tapping Screws. Attach the Retainer to each Side bow with four (4) #8 x 1/2" Tapping Screws. 1/4" Clevis Pin #4 Bow Install Header / Bow Assembly on Vehicle Lay the Header/Bow Assembly on top of the #4 Bow with the #3 Bow facing forward. Orient one end of the #3 Bow so it is outboard of the Bow Mount Bracket. Place one (1) 1/4" Washer between the bow and bracket and install a 1/4" Clevis Pin with another 1/4" Washer between the bracket and the Hitch Pin Clip. Repeat this on the other side of the vehicle. Underside of Top Fabric Header Retainer #8 x 1/2" Tapping Screws Hitch Pin Clip 1/4" Washers Bow Mount Bracket #3 Bow #4 Bow Use Masking Tape to hold fabric against Header Rev. 7 Supertop® with Tinted Windows ­ Installation Instructions Secure Header Retainer Flip the fabric over to access the Header. Secure the right and left rear corners of the retainer to the Header with two (2) #10-24 x 3/8" Screws and #1024 Silver Hex Nuts. Push a 1/8" x 3/8" Plastic Cap onto the points of each of the tapping screws. Underside of Top Fabric Header 1/8" x 3/8" Plastic Caps Hook Sunrider Latch over Side Bow Bushing Secure Sunrider Latches Open the top and lift it over the rear cab of the vehicle. Hook each Sunrider Latch securely over each Rear Side Bow Bushing. #10-24 x 3/8" Screw with #10-24 Silver Hex Nut Secure Top Fabric Retainer to Header Retainer Fold the front corner of the fabric around the header. Insert a #1 Phillips Screwdriver into the rear hole in the deck retainer and into the header retainer. Use the Screwdriver as a pry bar to stretch the deck rearward until the front retainer holes line up. Attach each deck retainer to the header retainer with two (2) #8 x 1/2" Tapping Screws. Secure Top Fabric to Bows Raise the header slightly and locate the hook and loop bow flap. Locate the long fabric bow flap and position the flap holes over the holes in the #3 Bow. Secure the flap to the bow with four (4) #8 x 1/2" Tapping Screws. Then hold up the top of the window with one hand and close the zipper with the other. The zipper is sandwiched between layers of fabric in the corners so be careful not to catch extra fabric in the zipper. Make sure that the Tailgate Bar is centered and is securely in the mounts. Then tuck the flaps on the Rear Window under the top fabric. Roll Plastic into Channel Install Tailgate Retainer on Rear Window Remove the Rear Window from the box and lay it flat with the backing side up. Orient the retainer with the round seal down and slide the "C" channel on the retainer onto the tubed strip sewn to the backing side of the Rear Window. Rear Window Tuck Flaps under top Install Tailgate Retainer on Vehicle Hook the bottom of each clip on the bottom of the Tailgate Retainer under the rear edge of the belt rail. Roll the retainer toward the inside of the vehicle until it clips into place. Tailgate Retainer Start Zipper Tailgate Retainer Pull both sliders down as far as possible to catch pin Belt Rail Rev. 10 Supertop® with Tinted Windows ­ Installation Instructions When operating the vehicle without the Quarter Windows, remove the Rear Window for proper ventilation. To Fold the Top Down Collapse Top Release the front of the top from the windshield. [. . . ] Damage to our products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under this warranty. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR REPLACE-A-TOPTM, SAILCLOTH REPLACE-A-TOPTM, SUPERTOP®, SUPERTOP® REPLACEMENT SKINS, SUNRIDER®, AND TIGERTOP®: TWO YEARS FROM DATE OF PURCHASE. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER "SOFT GOODS" MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS, AND/OR FOAM): ONE YEAR FROM DATE OF PURCHASE. THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER "HARD GOODS" MANUFACTURED BY OUR COMPANY (USING PRIMARILY METALS, PLASTICS, AND/OR FIBERGLASS): ONE YEAR FROM DATE OF PURCHASE. [. . . ]