User manual BERTAZZONI H366GGVNE

[. . . ] Installation, Service and User Instructions FREESTANDING GAS RANGES BERTAZZONI DIMENSIONS: 36'' (911 mm)(W) x 25 1/8'' (640 mm)(D) x36'' (911 mm)(H) MODELS H366GGVCR H366GGVNE H366GGVVI [M3Y0GTV4D(2 or 5)A] [M3Y0GTV4N(2 or 5)A] [M3Y0GTV4L(2 or 5)A] 310291 IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanently affixed labels, warnings, or plates from the product. -The installer should leave these instructions with the consumer who should retain for local inspector's use and for future reference. Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code NSIZ223. 1-latest edition. [. . . ] and it is pre-arranged from the factory to operate with one of these gas/pressure as indicated in the labels affixed on the appliance, package and Instruction booklet. To convert the regulator for use with other types of gas follow these instructions: 1) Unscrew by hand the upper metal stopper of the regulator. 2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again in opposite way under the metal stopper (for gas reference see the written "LP" and "NAT" with relative indicating arrows on the white piece). 3) Screw again by hand the metal stopper in the original position on the regulator. Following these exact instructions the gas regulator is converted for use with the other gas/pressure. It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage 12 - CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burners and unscrew the nozzles ( Fig. ) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE shown below. Follow the instructions below to change the oven burner nozzle: 1) Remove the oven level (Fig. 2) Loosen the screw V and pull out the burner from the support being careful not to damage the ignition plug and the thermocouple (Fig. 10-11) using a 10 mm spanner and replace it with the nozzle needed for the new type of gas according to what is indicated in TABLE shown below. Follow the instructions below to change the broiler burner nozzle: 1) Loosen the screw and pull out the burner from the support being careful not to damage the ignition plug and the thermocouple (Fig. 12) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas according to what is indicated in TABLE shown below. 13 Models H366GGV Burner Auxiliary Semi-Rapid Rapid Position Front R Rear L & C Front C Rear R Front L Inner Dual Burner Front L Outer Oven Broiler Oven downside Oven upside [M3Y0GTV4(L, N, D)(2 or 5)A] Gas Type NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) Pressure [i. w. c. ] 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" Max Rate [BTU/h] [W] 3400 996 3400 996 6100 1787 6100 1787 10400 3047 10400 3047 2800 820 2800 820 12000 3516 12000 3516 16000 4688 16000 4688 14500 4248 14500 4248 Min Rate [BTU/h] [W] 900 264 900 264 1500 439 1500 439 2500 732 2500 732 900 264 900 264 4500 1318 4500 1318 4000 1172 4000 1172 Only Max Only Max Only Max Only Max By-pass diam. [mm] Regulated 0, 29 Regulated 0, 36 Regulated 0, 47 Regulated 0, 29 Regulated 0, 65 Regulated 0, 60 No by-pass No by-pass Adapting to different types of gas Injector diam. [mm. ] 0, 90 0, 54 1, 18 0, 70 1, 55 0, 92 0, 80 0, 49 N°2 x 1, 15 N°2 x 0, 70 2, 00 1, 15 1, 90 1, 10 Models H365GGV [M3W0GTV4(L, N, D)(2 or 5)A] Adapting to different types of gas Burner Auxiliary Semi-Rapid Rapid Position Front R Rear L and R Front L Centre Inner Dual Burner Centre Outer Oven Broiler Oven downside Oven upside Injector diam. [mm. ] 0, 90 0, 54 1, 18 0, 70 1, 55 0, 92 0, 80 0, 49 N°2 x 1, 15 N°2 x 0, 70 2, 00 1, 15 1, 90 1, 10 Gas Type NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) NG LP (Propane) Pressure [i. w. c. ] 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" 4" 11" Max Rate [BTU/h] [W] 3400 996 3400 996 6100 1787 6100 1787 10400 3047 10400 3047 2800 820 2800 820 12000 3516 12000 3516 16000 4688 16000 4688 14500 4248 14500 4248 Min Rate [BTU/h] [W] 900 264 900 264 1500 439 1500 439 2500 732 2500 732 900 264 900 264 4500 1318 4500 1318 4000 1172 4000 1172 Only Max Only Max Only Max Only Max By-pass diam. [mm] Regulated 0, 29 Regulated 0, 36 Regulated 0, 47 Regulated 0, 29 Regulated 0, 65 Regulated 0, 60 No by-pass No by-pass CAUTION: save the orifices removed from the appliance for future use REGULATION OF BURNERS Primary air adjustment: Oven burner adjustment: follow the instructions below to adjust the primary air for the over burner: 1) Remove the oven bottom. 2) Loosen the screw P and adjust the position X of the Venturi cone (Fig. Broiler burner adjustment: to adjust the broiler burner loosen screw P and adjust the position X of the Venturi cone (Fig. 14) according to the measurements indicated in table 4. TABLE N°4: Burner primary air regulation (indicative) Type of gas NG (Natural Gas) LP (Propane Gas) Burner Oven Broiler Inches (mm) Inches (mm) 6/16 (9) fully open 1/2 (13) fully open 14 Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum: 1) Light the burner and set the knob to the MINIMUM position (small flame). 2) Remove the knob of the valve that is press fit on the rod of that valve. 3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body and turn the choke screw to the right or left until the burner flame is adjusted to minimum 4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position. Oven burner adjustment: follow the instructions below to adjust the minimum: 1) Light the burner setting the knob to the MAXIMUM position. 3) Set the knob to the MINIMUM position (corresponding to 250°F/120°C) and then remove it. 4) With a slotted screwdriver turn the choking screw (by-pass screw at the left side of the thermostat bar) and, while observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position. WARNING: The above-mentioned adjustment should be made only for natural gas, while for operation with liquid gas the screw must be locked at the end in a clockwise direction. The broiler burner always operates at maximum and therefore no minimum adjustment is required. SERVICE & MAINTENANCE INSTRUCTIONS Service and maintenance only to be carried out by an authorised person To replace parts such as burners, valves and electric components, the appliance must be open removing the worktop. [. . . ] Intensive and continuous use of the appliance may require additional ventilation, for example by opening a window, or increasing the power of the mechanical exhaust fan/range hood, if installed. Note: the cooker is equipped with the cooling fan that starts operation each time the oven knob is on a position different from 0 (zero). The fan circulates the air between the control panel and the oven door and also allows the control panel and the oven door stay at a warm temperature during the appliance operation in any condition. 21 CLEANING THE APPLIANCE: Never use abrasive cleaners Before cleaning the appliance it should be disconnected from the power supply. Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using warm water. [. . . ]