User manual BERTAZZONI DH1026

[. . . ] The gas appliance pressure regulator must be set for the gas with which the appliance is used. It is shipped from the factory adjusted for use with Natural Gas: CONVERSION FIXED ORIFICES ARE LOCATEDIN THE LITERATURE PACK SUPPLIED WITH THE UNIT. Injectors kit for the change of type of gas are contained inside the package jointly with the hob installation kit and Instruction booklet. The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 20'' water column (5 kPa) . [. . . ] Any other downward facing combustible surface less than 600mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area. However, in no case shall this clearance to any surface be less than 173/4"(450mm. Side clearances (Minimum values) The different side clearances shall be in accordance with the minimum values indicated in the table n. 1- 2 The cooking surface area is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs. Clearance between the front edge of the appliance and the front edge of the cabinet. Clearance between the left/right side edge of the appliance and the side wall (if present). To prevent liquids from leaking accidentally into the underlying storage space, the appliance is equipped with a special gasket. Lay out the protective sealing strips along the edges of the opening in the bench top and carefully overlap the strip end. With a screwdriver assemble the brackets A to the hotplate bottom by means of the screws B. Trim the part of the sealing strips which extend beyond the hotplate base Before connecting the appliance to the gas supply, first remove the plastic plug on which is pressfitted into the gas inlet union; to remove, just pull it off. This appliance shall be installed in accordance with installation requirements of the local gas authority of the appropriate installation code. 8) and turn the choke screw to the right or left until the flame of the burner is regulated in the most suitable way to MINIMUM. 4) Make sure that that the flame does not go out when changing the position quickly from MAXIMUM to the MINIMUM position. ATTENTION: The regulation described above can be carried out only with burners using natural gas, while with burners using propane gas the screw must be fully screwed in, in a clockwise direction. Adaptation of the pressure regulator for use with different type of gas The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with Natural Gas at a nominal outlet pressure of 4" w. And it is pre-arranged from the factory to operate with one of these gas/pressure as indicated in the pre-arranging labels affixed on the appliance, package and Instruction booklet. To convert the regulator for use with the other gas different from which one it is pre-arranged it is enough perform the following operations: 1) Unscrew by hand the upper metal stopper of the regulator (Fig. 2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again in opposite way under the metal stopper (for gas reference see the written "LP" and "NAT" with relative indicating arrows on the white piece). 3) Screw again by hand the metal stopper in the original position on the regulator. Operating in this way the gas regulator is converted for use with the other gas/pressure. Service and maintenance only to be carried out by an authorised person To replace parts such as burners, valves and electric components, the hotplate must be removed from the bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotplate top and finally replacing the defective parts. Note: if the valves must be replaced, first disassemble the ignitions switches wires. [. . . ] WARNINGS: Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquid. Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place in order to avoid potential hazards. Do not use aerosol sprays in the vicinity of this appliance while it is in operation For description of hotplates refer to installation instructions. A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. [. . . ]