User manual BERNEX GB41308 CATALOGUE 2010

[. . . ] 3-6 HDMI Supported Primary Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of BERNEXTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by BERNEX; or (2) the serial number of the product is defaced or missing. BERNEX PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL BERNEX, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF BERNEX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY BERNEX. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. As an Energy Star® Partner, our company has determined that this product meets the Energy Star® guidelines for energy efficiency. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. iii Safety information • • • • • • • • • • • • • • Before setting up the monitor, carefully read all the documentation that came with the package. The dangerous high voltages inside the monitor may result in serious physical injury. To prevent fire or shock hazard, never expose the monitor to rain or moisture. If the power supply is broken, do not try to fix it by yourself. Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. Slots and openings on the back or top of the cabinet are provided for ventilation. Never place this product near or over a radiator or heat source unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Button: button: 2. 3. 4. Press this button to decrease the value of the function selected or move to the next function. MENU Button: • Activate OSD menu • Press this button to enter/select the icon (function) highlighted while the OSD menu is activated. • • Press this button to increase the value of the function selected or move to the previous function. Input Select Button Use this hotkey to switch between VGA and HDMI input signals. Button: 5. • 1-4 Chapter 1: Product introduction 6. • Power button / Power indicator Press this button to turn the monitor on/off. Status White White (Blinking) OFF Description ON Standby mode OFF 1. 5. 2 Rear of the LED monitor Rear connectors DC-IN VGA HDMI 1 2 3 4 VGA port DC-IN port HDMI-IN port HDMI Audio - out port BERNEX LED Monitor MS228H Series 1-5 2. 1 • Adjusting the monitor Hold both right and left front frames to prevent the monitor from falling when you change its angle. • You can adjust the monitor’s angle from 10º to 20º. 2-1 Chapter 2: Setup 3. 1 3. 1. 1 1. OSD (On-Screen Display) menu How to reconfigure Press the MENU button to activate the OSD menu. Night View Mode 2. 3. 4. Press and to navigate through the functions. Highlight and activate the desired function by pressing the MENU button. If the function selected has a sub-menu, press and again to navigate through the sub-menu functions. Highlight and activate the desired sub-menu function by pressing the MENU button. Repeat step 2 and step 3 to 3. 1. 2 1. OSD Function Introduction Splendid This function contains five sub-functions you can select for your preference. Each mode has the Reset selection, allowing you to maintain your setting or return to the preset mode. [. . . ] Contrast: the adjusting range is from 0 to 100. is a hotkey to ASCR: Select YES or NO to enable or disable dynamic contrast ratio function. Trace Free: Sharpness: the adjusting range is from 0 to 100. Dimension (WxHxD) Box Dimension (WxHxD) Net Weight (Esti. ) Gross Weight (Esti. ) Voltage Rating *Specifications are subject to change without notice. 3-4 Chapter 3: General Instruction 3. 3 Troubleshooting (FAQ) Problem Possible Solution • Press the button to check if the monitor is in the ON mode. • Check if the power cord is properly connected to the monitor and the power outlet. • Make sure the signal cable is properly connected the monitor and the computer. [. . . ]