User manual BERNEX GB21105 CATALOGUE 2010

[. . . ] No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without BERNEX's prior written permission. Documentation Classifications In order to assist in the use of this product, BERNEX provides the following types of documentations:    For quick set-up of the product, read the Quick Installation Guide included with the product. For detailed product information, carefully read the User's Manual. For instructions on how to use BERNEX's unique features, read or download the information on/from the Support&Downloads\Motherboard\Technology Guide page on our website. For product-related information, check on our website at: http://www. gigabyte. com. tw Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X. X. " For example, "REV: 1. 0" means the revision of the motherboard is 1. 0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. [. . . ] (Default) System A password is required for booting the system and for entering the BIOS Setup program. HDD S. M. A. R. T. (Self Monitoring and Reporting Technology) capability of your hard drive. This feature allows your system to report read/write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed. (Default: Enabled) (Note) This item is present only if you install a CPU that supports this feature. For more information about Intel CPUs' unique features, please visit Intel's website. - 43 BIOS Setup CPU Multi-Threading (Note) Allows you to determine whether to enable all CPU cores and multi-threading function when using an Intel CPU that supports multi-core technology. This feature only works for operating systems that support multi-processor mode. (Default) Disabled Enables only one CPU core. Limit CPUID Max. to 3 (Note) No-Execute Memory Protect (Note) Allows you to determine whether to limit CPUID maximum value. Set this item to Disabled for Windows XP operating system; set this item to Enabled for legacy operating system such as Windows NT4. 0. (Default: Disabled) Enables or disables Intel Execute Disable Bit function. Non-Combined Sets all SATA devices to operate in PATA mode and disables the integrated IDE controller. PATA IDE Set to SATA Port 0/2 Set to This item is configurable only if the On-Chip SATA Mode is set to Combined. Disabled Disables the integrated IDE controller when Non-Combined is selected. This value is dependent on the On-Chip SATA Mode and PATA IDE Set to settings. 0 Master/Slave. BIOS Setup - 46 - SATA Port 1/3 Set to This value is dependent on the On-Chip SATA Mode and PATA IDE Set to settings. (Default: Auto) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled. (Default: Enabled) If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to Disabled. When the onboard LAN function and Green LAN are enabled, the system will dynamically detect if a LAN cable is connected or not. If not, the corresponding LAN controller will be disabled automatically. (Default: Disabled) CMOS Setup Utility-Copyright (C) 1984-2009 Award Software SMART LAN Start detecting at Port. . . . . Part1-2 Status = Open Part3-6 Status = Open Part4-5 Status = Open Part7-8 Status = Open / / / / Length Length Length Length = = = = 0m 0m 0m 0m Item Help Menu Level  Azalia Codec Onboard H/W LAN Green LAN SMART LAN (LAN Cable Diagnostic Function) Enter: Select : Move F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to the following information for diagnosing your LAN cable: When No LAN Cable Is Attached. . . [. . . ] Reinstall other devices one by one (install one device at one time and then boot the system to see if the device works successfully). No The IDE/SATA device, connector, or cable might fail. The problem is verified and solved. END If the procedure above is unable to solve your problem, contact the place of purchase or local dealer for help. Or go to the Support&Downloads\Technical Service Zone page to submit your question. Our customer service staff will reply you as soon as possible. Appendix - 82 - 5-3 Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose. We believe that the information contained herein was accurate in all respects at the time of printing. [. . . ]