User manual BENSHAW STANDARD KEYPAD

[. . . ] Measure the DC Bus charge between B+ and B- terminals, ensure DC voltage is below 45V before proceeding. Do not connect or disconnect the wires to or from inverter when power is applied. CAUTION 1. Service only by qualified personnel. 2. Make sure power-up restart is off to prevent any unexpected operation of the motor. [. . . ] NEMA 4 UL Type 4 is the standard rating for all keypads mounted on the enclosure door (contact factory if you request a different rating). On-Line Documentation 1. 2 On-Line Documentation All RSi SX drive and MX control documentation is available on-line at http://www. benshaw. com. Contacting Benshaw 1. 3 Contacting Benshaw Information about Benshaw products and services is available by contacting Benshaw at one of the following offices: Benshaw Inc. Sutter Road Glenshaw, PA 15116 United States of America Phone: (412) 487-8235 Fax: (412) 487-4201 Benshaw Canada Controls Inc. 550 Bright Street East Listowel, Ontario N4W 3W3 Canada Phone: (519) 291-5112 Fax: (519) 291-2595 Benshaw West 7820 E. Evans Drive, Suite 900 Scottsdale, AZ 85260 United States of America Phone: (480) 905-0601 Fax: (480) 905-0757 2 2 Mounting Keypad on Enclosure 3 2 - Mounting Keypad on Enclosure Mounting Keyp ad on Enc losur e 2 Introduction 2. 1 Introduction The integral LED keypad is located on the face of the MX Control, and provides local interface for changing and updating parameters. If you wish to install the optional LCD keypad onto an enclosure door, there are a few points you will need to understand first. The RSi SX comes with a standard LCD plain english and easy to use display conveniently installed on the face of the drive. . Standard Keypad Kits 2. 2 RSi SX Drive Standard Keypad Kits VFD-SX-2M-RKP-00 (Frame 0-2) Kit contains the following parts: · VFD-SKPASSBR, Simple Keypad for RSi SX drive · GKT-100016-00, Gasket NEMA 3R · VFD-2M-RE-CABLE-MX, 2 meter long cable · HW-STGBF6X1/2SZ, Plastite screws( self tapping), Qty 4 · MD-100001-00, Bezel VFD-SX-2M-RKP-03 (Frame 3 and up) Kit contains the following parts: · VFD-SKPASSBR, Simple Keypad for RSi SX drive · GKT-100016-00, Gasket NEMA 3R · VFD-2M-RE-CABLE-SX, 2 meter long cable · HW-STGBF6X1/2SZ, Plastite screws (self tapping), Qty 4 · MD-100001-00, Bezel 2. 3 MX Control Standard Keypad Kits MX-1M-RBK-00 Kit Contains the following parts: · KPMALCDSKP, Simple Keypad for MX Control · GKT-100018-00 and 100018-01, Gasket · MD-100001-00, Bezel · HW-STGBF6X1/2SZ, Plastite screws (self tapping), Qty 4 · VFD-2M-RE-CABLE-SX, 1 meter long cable MX-2M-RBX-00 Kit Contains the following parts: · KPMALCDSKP, Simple Keypad for MX Control · GKT-100018-00 and 100018-01, Gasket · MD-100001-00, Bezel · HW-STGBF6X1/2SZ, Plastite screws (self tapping), Qty 4 · VFD-2M-RE-CABLE-SX, 2 meter long cable 4 2 - Mounting Keypad on Enclosure Drilling Keypad Holes in Enclosure Door 2. 4 Drilling Keypad Holes in Enclosure Door Using the drill template (see Appendix on page 15) as a guide, mark the holes you will need to drill into the enclosure door. z NOTE: Refer to the Appendix on page 15 for the actual drill template. Mounting Keypad to the Enclosure Door 2. 5 Mounting Keypad to the Enclosure Door Before you begin the installation insert the gasket (GKT-100016-00) between the backside of the kaypad and the bezel (MD-100001-00) prior to attaching the screws. Using four of the eight screws provided in the kit, follow figure 1 to mount the keypad to the bezel. A second gasket (GKT-100016-01) is to be place on the backside of the bezel (see figure 1) with the addition of the gaskets and bezel this keypad now has a NEMA 4 enviromental rating. . You will then need to attach the cable, which should be 2 meters in length, from the drive to the keypad on the enclosure door. Refer to the images below figure 4 to fasten the cable provided in the kit. Pay close attention as to which side the red wire on the cable is to be attached. Figure 1 Figure 2 5 2 - Mounting Keypad on Enclosure Figure 3 below show the drill template for the installation of the bezel. The bezel is a standard component on all Benshaw MX controls and RSi SX Drives. With the bezel installed the unit acheives a NEMA 4 enviromental rating. Figure 3: Bezel Drill Template 4 5/8" 2 5/16" Ø3/16" THRU (4 PLACES) May not be printed to scale 3 3/4" Ø1" THRU 25/32" zNOTES: The drilling template for the bezel is may not be printed to scale. 6 2 - Mounting Keypad on Enclosure The following figure give you the order in which to mount the keypad to the enclosure door. It is up to you where the keypad will be located on the enclosure door. Figure 4 On Back of Display Red Wire Red Wire 7 2 - Mounting Keypad on Enclosure Requirements for the NEMA 4 Enviromental Rating 2. 6 Requirements for NEMA4 Figures 5 and 5a, show the bezel that is required to obtain a NEMA 4 rating (Gaskets not in photo) Figures 6 show an example of what the installation should like when complete. Figure 7 show an up close view keypad Bezel already installed. Figure 5a Figure 5 Figure 6 Figure 7 8 2 - Mounting Keypad on Enclosure Interface Card Installation 2. 7 Interface Card The MX Control RediStart Soft Starter uses an interface card (BIPC-300049-01). The interface card is used to connect the units display to the control. zNOTE: Lock out control from all power sources before installation. MX Control without Interface Card Interface Card (top view) Interface Card (bottom view) 1. Attach 20 pin header to the bottom of the interface card. 9 2 - Mounting Keypad on Enclosure 2. Remember to remove the adhesive strip. 3. Attach header and interface card assemblly to the MX Control Board. 4. [. . . ] It may be easier to remove the Display Drill Template page from this manual. Making sure that the drill template is level, tape it to the enclosure door where the mounting location was decided. Using template as your guide, drill one 1" and four 3/16" holes into the mounting surface, and then debur all of the holes. [. . . ]