User manual BENSHAW RSI (S-SERIES) METASYS N2 CARD

[. . . ] Be sure to remove all AC power from the drive and wait at least 3 minutes before servicing. If the bus capacitor discharge circuit fails, high voltage can remain in the drive a long time after the AC power is removed. Service only by qualified personnel. 1 Revision History Revision 00 Date 8/20/2001 ECO# E0128 Description of Changes Initial release. Publication #: 890014-10-00 2 TABLE OF CONTENTS 1. [. . . ] I/O Point Map The drive may be configured, controlled and monitored through a set of analog input, analog output, binary input and binary output points or objects. The following tables describe all of the inputs and outputs defined by the drive's Metasys N2 card. The heading NPA stands for Network Point Address. 3. 1 Analog Outputs Analog Output (AO) objects are used to configure the drive. AO objects will not report an override active status and issuing an override release command will not restore an AO object to its previous value. AO objects do not support Change of State (COS). NPT NPA Units Description Range / Value Notes Can not be set higher than the Freq. 0. 00 ­ 400. 00 The drive only uses this value if the Frequency Set parameter (AO-4) is set to Remote. AO 2 Sec Accel Time 0. 0 ­ 6000. 0 The drive only uses this value if the Frequency Set parameter (AO-4) is set to Remote. AO 3 Sec Decel Time 0. 0 ­ 6000. 0 0 ­ Key 1 ­ Terminal 2 ­ Remote 0 ­ Key 1 ­ Terminal-1 2 ­ Terminal-2 3 ­ Remote The drive only uses this value if the Frequency Set parameter (AO-4) is set to Remote. AO 4 Frequency Set AO 1 Hz Command Frequency AO 5 - Run/Stop Set 7 I/O POINT MAP 3. 2 Binary Outputs Binary Output (BO) objects are used to control the drive. BO objects will not report an override active status and issuing an override release command will not restore a BO object to its previous value. BO objects do not support the Minimum On-time, Minimum Off-time or Maximum cycles per hour functions. NPT BO BO BO BO BO NPA 1 2 3 4 5 Description Stop Run Forward Run Reverse Reset Fault Coast to Stop (BX function) Range / Value 1 ­ Stop 1 ­ Run Forward 1 ­ Run Reverse 1 ­ Reset 1 ­ Coast The drive may be stopped by resetting this to 0 or by setting BO-1 to 1 or by setting BO-5 to 1. The drive may be stopped by resetting this to 0 or by setting BO-1 to 1 or by setting BO-5 to 1. Notes 3. 3 Analog Inputs Analog Input (AI) objects are used to monitor the drive. AI objects support high and low warning limits, high and low alarm limits and differential values. COS, warning and alarm functions may be individually enabled or disabled. AI objects do not support the override function. NPT AI AI AI NPA 1 2 3 Units Amps Hz RPM Description Output Current Output Frequency Output Speed 0 ­ No fault 1 ­ OC 2 ­ OV 4 ­ EXT 8 ­ BX 16 ­ LV 32 ­ FUSE 64 ­ GF 128 ­ OH 256 ­ ETH 512 ­ OLT Range / Value AI 4 - Fault Code 8 I/O POINT MAP 3. 4 Binary Inputs Binary Input (BI) objects are used to monitor the drive. [. . . ] Benshaw technical field support personnel are available to conduct on-site training on RSi S-Series Inverter operations and troubleshooting. Benshaw technical support personnel are available (at no charge) to answer customer questions and provide technical support over the telephone. Benshaw provides all customers with: · Operations manual · Wiring diagram All drawings are produced in AutoCAD© format. [. . . ]