User manual BENSHAW RE-FLASH

[. . . ] Publication #890020-11-00 RSi Series Drive Re-Flash Tool & Procedure Manual The Leader In Solid State Motor Control Technology © 2003 Benshaw Inc. All Rights Reserved TRADEMARK NOTICE Benshaw and are registered trademarks of Benshaw Incorporated. ModBUS is a registered trademark of Schneider Electric. UL is a trademark of Underwriters Laboratories, Incorporated. TABLE OF CONTENTS TABLE OF CONTENTS 1 INTRODUCTION . 16 4. 3. 1 Connections Using a Serial converter from B & B Electronics or Third Party) . [. . . ] If you are using a third party translator you will have to make a cable to connect the device to the product being re-flashed. · On a SX Sensorless Vector Drive, connection is to the TSP board. The connector is at the top of the board and slightly right of center. · On an SX Sensorless Vector Drive, connection is to the Modbus port. The connector is at the bottom center of the Terminal Strip Processor board. · On an Enhanced Keypad (EKP), connection is to the RJ45 connector on the back of the keypad. An external power supply is required when connecting to the EKP, 24 VDC at 50mA. 4. 5. 7. 8. 16 4 - RE-FLASH TOOL CONNECTION Figure 8: Connection using inline RS232 to RS485 Converter In line RS232 to RS485 converter from B&B Electronics Cable WI-400004-00 Re-Flash Cable WI0400002-00 USB to RS232 4. 4 Connections Using A RS422/485 PCMCIA Card 4. 4. 1 Introduction to Quatech SSP 200/300 RS422/485 PCMCIA card The PCMCIA card is an excellent way for PC notebooks to obtain an RS485 interface when there is no RS232 port. An alternate method would be to use a USB adapter and an inline RS232 to RS485 interface. When installed the PC software will activate the plug and play, NEW HARDWARE FOUND. With the NEW Found Hardware box displayed on the screen select "Install Hardware Driver". Select "Search for suitable driver for my device", press NEXT button. If the CD is the "D" drive, the following file should be selected "d:\serial port adapter\drivers\ Window 2000, XP for PCI, PCMCIA\qserbrd. inf", press NEXT button. A message "Completing the Found NEW Hardware Wizard, press Finish button. 17 4 - RE-FLASH TOOL CONNECTION 4. 4. 3 Card Configuration After installation is complete the card has to be configured to correct operation 1. In the list of device managers, select "Multi-Port Serial Adapters" 7. Then select "Quatech SSP 200/300 PCMCIA RS422/485 serial adapter" Double Click 8. RS422/485 Duplex mode, "AUTO Toggle", (Changed from Default) · D. In the list of device managers, select "Select Ports (COM & LPT)" · Communication Ports (COM1) · ECP Printer Port (LPT1) · Quatech PCMCIA Serial Port (COM5) 12. Select Port Setting Tab · Bits per Second: 9600 · Data Bits: 8 · Parity: None · Stop Bits: 1 · Flow Control: None 14. Select "Advance" button Select COM Port Assignment, many PC's will COM 1-COM 4 "in use" COM 5 is OK to use for the Drive Reflash Tool 15. The PCMCIA card is ready to operate. Figure 9: RS422/485 PCMCIA Card TSP EKP Port PCMCIA Card, RS422/485 Cable WI-400003-00 Re-Flash Cable WI-400002-00 SX 18 5 Using the Re-Flash Tool 19 5 - USING THE RE-FLASH TOOL Using the Re-flash Tool 5. 1 Re-flashing the Drive Place the drive in re-flash mode as defined in the following sections. [. . . ] This assures that the drive will not run until programming has been completed. Confirm the Re-flash Configuration settings in the Re-flash Configuration panel of the DRT. On completion of the download, the DRT can be closed and the Re-flash cable disconnected from the EKP port. The factory reset "Par STO/RCL" can be found at AFN 84, AFN 85, and AFN 87 depending on the level of application software. 2. [. . . ]