User manual BENQ VP150X

[. . . ] ULTRA PORTABLE PROJECTOR VP150X USER'S GUIDE Thank you for purchasing Benq Ultra Portable Projector. Please read this user's guide to ensure correct use of the device. Save this user's guide for future reference. OUTLINE This Ultra Portable Projector can display various computer signals and NTSC/PAL/SECAM video signals. FEATURES 1. USB Communication Copyright Copyright © 2002 by Benq Corporation, formerly Acer Communications & Multimedia Inc. . [. . . ] Connect to notebook 6 English Connect the Projector to Macintosh Control Port Output Mouse Cable for PS/2 Port (Supplied) Control Port ADB Port Input Computer Input Computer output VGA/MAC Adapter (Supplied) VGA Cable (supplied) Computer in Figure 10. Connect to Macintosh Connect the Projector to Power Book Mouse Cable for PS/2 Port (Supplied) Control Port Output Control Port ADB Port Input Computer Input Computer output VGA Cable (supplied) Computer in VGA/MAC Adapter (Supplied) Figure 11. Connect to Power Book Connect to Video/ S-Video S-Video VHS (DVD Player) AV Figure 12. Connect to Video, S-Video Connection 7 OPERATION Turn On/Off Procedure A Power on 3 Press the Standby/On key to turn on the lamp. "INPUT SIGNAL DETECTED, ACTIVATING AUTO IMAGE" will be displayed on the screen after the projector identifies the input signal. "SEARCHING" message will be displayed on the screen if there is no signal input. "SYNC IS OUT OF RANGE" message will be displayed on the screen if the horizontal frequency of the input signal exceeds the range of the projector. B Standby Press the Standby/On key for more than one second to turn off the lamp. The LED will then blink orange and the lamp will shut down, but the fans will continue to run for about 1 minutes to cool the lamp. *Lamp Protection Procedure: If you try to turn on the lamp again while the LED is blinking, the projector will ignore the command until it is cooled down for one minute. External Control A Control Pad Lampr status indicator Standby/On indicator Menu STANDBY/ON SOURCE EXIT Figure 13. External control pad 8 English MAIN UNIT Menu To call the OSD menu. To select items. FUNCTION To navigate through sub pages or to increase/decrease the scale bar number. Exit To exit from the current page or OSD menu, and save setting changes. i-key Source Standby/On Standby/On indicator Lamp status indicator To adjust position, phase automatically. Lights or blinks when the lamp does not light. B Remote Control LED STANDBY/ON SOURCE LASER MENU MOUSE FREEZE EXIT PAN BLANK L-CLICK DRAG R-CLICK MAGNIFY RETURN VOLUME i -KEY Figure 14. Remote control Operation 9 The remote control allows you to operate the function keys on the projector and to emulate mouse function when the projector is connected to a computer. Main Unit Standby/On Freeze Magnify Function To turn the projection lamp on and off. (Move the picture with the Disk Pad after pressing the Magnify button. ) Disk Pad When the OSD menu is active, Disk Pad acts as selecting device. When the magnify function is active, use disk pad to move through the picture. And the blank screen will be revealed partially from top to bottom by pressing Blank again. The sound gets louder or quieter by pressing the "+" or "-" button. When operating in mouse emulation mode, it registers a left mouse click. When operating in mouse emulation mode, it registers a right mouse click. To adjust position, phase automatically. Menu Blank Source Return Volume Laser Mouse Left-Click Mouse Right-Click Exit i-key Inserting Batteries in the Remote Control Be sure to follow instructions in placing batteries into the remote control units. [. . . ] To set the time to turn the power off after the start up screen is displayed and no signal is detected or sync is out of range. Auto Select Auto and press " " or " " to reset display, image and control settings to factory settings. D Source Page This Sub-page will only show up whenever video, svideo is attached. There are five items on this page: Source, Volume, Treble, Bass, and Mute. Figure 24. Source sub-page (video, s-video) *The sequence of input signal detection: a. [. . . ]