User manual BENQ SL705S

[. . . ] Read this user's guide before you operate your projector and save it for future reference. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. Excessive operation of lamps beyond the rated life could cause them to explode on rare occasions. Never replace lamp assembly or any electronic components unless the projector is unplugged. [. . . ] Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Introduction 9 Benq Corporation INSTALLATION Screen Size Place the projector at the required distance from the screen according to the desired picture size (see the table below). L Projetion Distance Diagnal 30. 4 60. 8 91. 2 121. 5 151. 9 182. 3 213. 1 243. 1 273. 5 303. 9 Screen Size (Max. ) A. Height (cm) 61. 8 46. 3 123. 65 92. 7 185. 3 138. 9 247. 0 185. 2 308. 7 231. 6 370. 5 277. 9 432. 2 324. 18 494. 0 370. 5 555. 7 416. 7 617. 5 463. 11 L. Projection distance (cm) 100 200 300 400 500 600 700 800 900 1000 Screen Size (Min. ) B. Height (cm) 50. 7 38. 0 101. 3 76. 0 151. 9 113. 9 202. 5 151. 9 253. 2 189. 9 303. 8 227. 9 354. 4 266. 2 405. 1 303. 8 455. 7 341. 8 506. 3 379. 8 Connecting to Various Equipment It only takes a few seconds to connect your projector to your computer/notebook, VCR or other systems. However, a Mac adapter (an optional accessory) is needed for connection for Macintosh users. Computer/ HDTV S-Video/ Video Audio Video S-Video 10 Installation User's Manual OPERATION Start Up 1. Press POWER for 1 second. Projector Remote Control Power Power · The back-lit POWER key blinks green and stays green when the power is turned on. (When the power is turned off, there is a 60-second cooling period before the projector can be re-started. ) Switch on all connected equipment. 3. Operation 11 Benq Corporation Digital Keystone Correction Keystoning is when the projected image is noticeably wider on either the top or bottom. To correct this, press KEYSTONE +/- (hot key) on the control panel of the projector or on the remote control, then adjust the sliding bar labeled Keystone, as needed. Press - to correct keystoning at the bottom of the image. Projector Auto Source Remote control Auto Adjustment In some cases, you may have to optimize the picture quality manually. To do this, press the AUTO key on the control panel of the projector or on the remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust to the best picture quality. Projector Remote control Auto Auto Source 12 Operation User's Manual Source Selection When several input sources are available, press the SOURCE key to make a selection from the control panel of the projector or the remote control. Projector Remote control Power Source Auto Source Power Menu System Press Menu for the main menu and press 3or again to select items in the sub-menu. Menu Bar Sub-menu Display Keystone Brightness Contrast Phase H. Size Image Auto resize H-position V-position Color Temp Information Auto resize H-position V-position Color Tint Color Temp Ratio System Sharpness Color Temp Information Source Mirror Source Volume Treble Bass Mute Control Langauge OSD OSD Time Auto Off Reset Lamp hour PIP Main page: PIP Source PIP Size PIP Pos. Position V. Position More Options Sub Page: Brightness Contrast Color Tint Sharpness System 4 to select a sub-menu. Press Menu PC Y/Pb/Pr Video Keystone Brightness Contrast Color Tint Operation 13 Benq Corporation 1. Brightness Adjusts the degree of difference between darkness and lightness of image. Contrast Adjusts to fit in the desired image size. Phase *This function is not available when the input modes are Video, SVideo. Adjusts to avoid the occurrence of flicker. H. Size Color Tint *This function is not available when the input modes are Video, SVideo. Adjusts to increase or decrease the colors (R, G, B) of image. *This function is not available when the input mode is PC. Adjusts to make the image look more red or blue. *This function is not available when the input mode is PC. 14 Operation User's Manual 2. Image Menu Makes the best fit of the image to the screen, Auto resize Adjusts the horizontal position of image. H-position Adjusts the vertical positon of image. V-position Color Temp. Information Ratio Adjusts the color temperature to fit your preference. 16:9 (Wide) *This function is not available when the input modes are PC, YPbPr. System 4 modes can be selected. *This function is not available when the input modes are PC, YPbPr. Sharpness Color Tint Adjusts to make the image look sharper or softer. *This function is not available when the input modes are PC, YPbPr. Adjusts to increase or decrease the colors (R, G, B) of image. *This function is not available when the input mode is PC. Adjusts to make the image look more red or blue. *This function is not available when the input mode is PC. Operation 15 Benq Corporation 3. [. . . ] Use the Keystone correction key on the control panel of the projector or the remote control unit. Press Auto on the control panel of the projector or the remote control unit to get better picture quality. Ensure the distance between the unit and screen is within the adjustment range of the lens. Make sure there is no obstacle between the remote control and the unit. [. . . ]