User manual BENQ CP220

[. . . ] CP220 Digital Projector Commuter Series User's Manual Welcome Copyright Copyright 2006 by BenQ Corporation. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation. Disclaimer BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. *DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. [. . . ] Take the (optional accessory) S-Video cable and connect one end to the S-Video output socket of the Video source device. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector. If you wish to make use of the projector (mixed mono) speaker, take a suitable audio cable and connect one end of the cable to the audio output sockets of the video device, and the other end to the AUDIO socket of the projector. Once connected, the audio can be controlled by the projector volume and mute settings. See "Mute (Off)" and "Volume (5)" on page 35 for details. The final connection path should be like that shown in the following diagram: A/V device S-Video cable Audio cable · · The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 17 for details. · Connection 19 Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: · If so, you can continue with this procedure. · If not, you will need to reassess which method you can use to connect to the device. Take the (optional accessory) Video cable and connect one end to the composite Video output socket of the Video source device. Connect the other end of the Video cable to the VIDEO socket on the projector. If you wish to make use of the projector (mixed mono) speaker, take a suitable audio cable and connect one end of the cable to the audio output sockets of the video device, and the other end to the AUDIO socket of the projector. Once connected, the audio can be controlled by the projector volume and mute settings. See "Mute (Off)" and "Volume (5)" on page 35 for details. The final connection path should be like that shown in the following diagram: A/V device Video cable Audio cable · · The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are unavailable for use. See "Connecting Video source devices" on page 17 for details. · 20 Connection Operation Start up 1. Check that the Power indicator on the projector lights orange after power has been applied. 2. Slide open the lens cover. If it is left closed, it could become deformed due to heat. 3. 4. 5. 6. Press and hold (for 2 seconds) the Power button on the remote control or projector to start the unit. [. . . ] Or Please contact your dealer for assistance. R Thermal events - R R R R G O R R R G - R G R R R R The projector has shutdown automatically. Please contact your dealer for assistance. - Maintenance 43 Troubleshooting THE PROJECTOR DOES NOT TURN ON. Cause There is no power from the power cable. Attempting to turn the projector on again during the cooling process. Remedy Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. Wait until the cooling down process has completed. NO PICTURE Cause The video source is not turned on or connected correctly. [. . . ]