User manual BELTRONICS RX65

[. . . ] Congratulations The BEL Pro RX65 is the most advanced radar, laser and safety detector ever designed by Beltronics. The BEL RX65 includes full X, K, SuperWide Ka, and Safety Warning System radar capability, front and rear laser detection, digital signal processing (DSP) for superior range and reduced false alarms, our patented Mute and AutoMute, audible and visual band alerts, and all the performance you'd expect from Beltronics. In addition, the BEL RX65 introduces a new level of revolutionary performance and innovative features. · Superior long-range radar and laser detection, including new "POP" mode alert · Advanced Programming lets you customize 7 features · AutoScan mode drastically reduces false alarms, plus Highway and City settings · Ultra-bright alphanumeric Display with 280 LEDs · Exclusive Threat Display tracks and displays multiple radar signals, including signal strength. [. . . ] Since the factory setting is for AutoMute to be on, RX65 will display aMute ON. (If you accidentally don't release the RVW button in time, and the RX65 goes to the next category, hold the RVW button down again, and after RX65 scrolls through all categories, it will begin again at the top of the list. ) 4 Press the CHG button to change from aMute ON to aMute OFF. 5 To complete the Programming, simply wait 8 seconds without pressing any button. The RX65 will display Complete, beep 4 times, and return to normal operation. Press the REVIEW button to go from one category to the next PILOT (Power-on indication) VOICE POWER-ON SEQUENCE SIGNAL STRENGTH METER Pilot HWY Pilot H Pilot V Voice ON Voice OFF PwrOn STD PwrOn FST Meter STD Meter THT Meter TEC aMute ON aMute OFF City STD City LoX City NoX Bands ALL Bands MOD Press the CHANGE button to change your setting within a category * Full word: Highway or AutoScan or City Letter: H or A or C Vehicle voltage * Voice alerts on Voice alerts off * Standard power-on sequence Fast power-on sequence * Standard signal strength meter Threat Display Tech Display * AutoMute on AutoMute off * Standard City mode sensitivity Low X band sensitivity in City Mode No X band sensitivity in City Mode * All bands enabled One or more bands are disabled Turn bands "ON" or "OFF" by pressing the VOLUME/MUTE button X K Ka POP Ku LSR SWS 13 How to use Programming AUTOMUTE CITY MODE SENSITIVITY BANDS * Factory Default Settings To reset RX65 to its original factory settings, press and hold the "CITY" and "BRT" buttons while turning the power on. The RX65's display will provide a "Reset" message, accompanied by an audible alert, acknowledging the reset. ON ON USA ON ON ON ON or or or or or or or OFF OFF Intl or OFF OFF OFF OFF OFF Details of Programming Pilot (Power-on indication) Note: When you are using the Dark mode, the display will only show HD, AD, or CD, (Highway-Dark, AutoScan-Dark, or CityDark). Pilot HWY (Full description) In this setting, RX65 will display "Highway, " "City, " or "Auto" as its power-on indication. (factory default) Pilot H (Letter) In this setting, RX65 will display "H" for Highway, "C" for City, and "A" for AutoScan. Pilot V (Vehicle voltage) In this setting, RX65 will continually display "H" for Highway, "C" for City, and "A" for AutoScan, and the vehicle's voltage. If the vehicle's voltage drops below 10. 5 volts, a low voltage warning is displayed, followed by an audible alert. A high voltage warning is also given if the voltage goes above 16. 0 volts. The high-voltage warning is also followed by an audible alert. Voice Voice On (Voice alerts on) In this setting, all radar, laser, and SWS (if programmed on) alerts will be accompanied by a digital voice. Voice Off (Voice alerts off) In this setting, only the audio tones will be heard during an alert or SWS message. Signal Strength Meter MeterSTD (Standard meter) In this setting, the meter displays the band of the received signal, and a bar graph shows the relative signal strength. (factory default) MeterTHT (Threat Display) In this setting, the meter simultaneously tracks multiple radar signals, including relative signal strength for each. Note: The Threat Display feature is explained in more detail on pages 10-11. MeterTEC (Tech Display meter) In this setting, the meter displays the actual numeric frequency of the radar signal received. Note: The Tech Display feature is explained in more detail on page 11. City Mode Sensitivity City STD (Standard) In this setting, when you put RX65 in the City mode, X-band sensitivity is significantly reduced, to reduce annoyance from X-band intrusion alarms and motion sensors. (factory default) City LoX (Low X band sensitivity) In this setting, when you put RX65 in the City mode, X-band sensitivity is reduced more than the standard setting. This will reduce X band alarms from other sources even further, but also significantly reduces range to X band traffic radar. City NoX (No X band sensitivity) In this setting, when you put RX65 in the City mode, it will not respond to any X band signals. WARNING: Only choose this setting if you are absolutely certain that there are no X band traffic radar units where you drive. X-band sensitivity is not affected when used in "AutoScan, " or "Highway" modes. Power-on Sequence PwrOnSTD (Standard) In this setting, each time you turn on the RX65, it will display "BEL RX65, " "Laser, " "Ka-band, " "K-band, " "X-band, " "Safety, " and any changes to factory settings. [. . . ] If the detector has been damaged, abused or modified, the repair cost will be calculated on a parts and labor basis. If it exceeds the basic repair charge, you will be contacted with a quotation. If the additional payment is not received within 30 days (or if you notify us that you choose not to have your RX65 repaired at the price quoted), your RX65 will be returned, without repair. Ship RX65 and Power Cord To: BELTRONICS Customer Service Department Service Order Number ______________ 5442 West Chester Road West Chester, Ohio 45069 For your own protection, we recommend that you ship your RX65 postpaid and insured. [. . . ]