User manual BELKIN P74978UKAP21000UK3M

[. . . ] Home Cinema Power Protection with PureFilterTM Technology Power Console PF40 User Manual AP21000uk3M Table of Contents Page PureAV Power Console Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Power Console Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turntables Note: You can connect any type of audio component into any of the audio filter sockets. You are not limited to the components listed above. PureAV Power Console 12 Hookup and Installation Step 7 Connect High-Current Audio Filter (8-Second Delay) The HiCurrentTM socket is specifically designed to filter out AC line noise while delivering maximum current to power-hungry amplifiers and other high-current audio components. This allows your high-current amplifiers to turn on last and turn off first, avoiding that annoying and potentially damaging "thump" from getting to your speakers. Attach PureAV power cable labels to each component's power cable before you plug the cable into the HiCurrent socket on the Power Console. Connect your high-current device into the "HiCurrent Filter". Examples of the most common high-current components are listed below: 1. Electrostatic Speakers Note: You can connect any type of high-current audio component into any of the high-current sockets. You are not limited to the components listed above. PureAV Power Console 13 Hookup and Installation Step 8 Connect your Pay-Per-View/Phone Line Your PureAV Power Console comes equipped with Pay-Per-View/phoneline protection with a built-in splitter. These are standard BT RJ11 phone ports and are labeled "Phone". Connect one end of your telephone cable to the wall port to which you normally connect your phone line. Connect the other end of your telephone cable to the Power Console phone port labeled "IN". Connect one end of the PureAV phone cable (included) to the Power Console phone port labeled "OUT". Connect the other end of this cable to the Pay-Per-View phone port on your cable TV or satellite receiver. To connect a telephone ­ Conanect one end of another phone cable to the other Power Console phone port labeled "OUT". Note: We have included labels for the "Phone IN" and "Phone OUT" lines, if needed, for better organisation. PureAV Power Console 14 Hookup and Installation Step 9 Connect your Cable TV/Satellite Coaxial Lines Your PureAV Power Console comes with two pairs of F-type coaxialcable connections, and one pair of aerial-cable connections to protect your system from dangerous electrical disturbances that can travel down your cable/satellite/aerial-signal lines. You will need additional coaxial cables to connect the Power Console to your home cinema components. Satellite (DSS) TV ­ Connect the incoming satellite television F-type coaxial-cable line to the connector labeled "SAT IN". Connect one end of a second coaxial cable to the connector labeled "SAT OUT". Cable TV ­ Connect the incoming cable television F-type coaxial-cable line to the connector labeled "Cable IN". Connect one end of a second coaxial cable to the connector labeled "Cable OUT". Antenna ­ Connect the incoming TV or radio antenna cable line to the connector labeled "Antenna IN". Connect one end of a second aerial cable to the connector labeled "Antenna OUT". [. . . ] Belkin reserves the right to review the damaged PureAV Power Console, the damaged equipment, and the site where the damage occurred. All costs of shipping the PureAV Power Console and the damaged equipment to Belkin for inspection shall be borne initially by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment to such repair facility and of such estimate shall be borne initially by the purchaser. [. . . ]