User manual BELKIN P74521-B

[. . . ] Home Theater Power Conditioner PF30L, PF31L, and PF40L User Manual AP11000-10 AP11200-12 AP11201-12 Table of Contents Page PureAV Power Conditioner Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Power Conditioner Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hookup and Installation Step 1 (optional) Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Mounting your Power Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A) by aligning the mounting holes on the back of the Power Conditioner (Fig. C) with the mounting screws on the surface of the wall-mount bracket (Fig. Use the wall-mount bracket as a template to mark the four screw locations on the mounting surface (Fig. A) by aligning the mounting holes on the back of the Power Conditioner (Fig. C) with the mounting screws on the surface of the wall-mount bracket (Fig. C (Mounting Holes) Mounting Holes 6 Hookup and Installation Step 2 Connect Audio Components to the Audio Filter (switched) Certain components do not need to be, or should not be, powered on at all times. For this reason, the audio filter outlets are "switched" and can be controlled with the button situated on top of the Power Conditioner unit labeled "Switched". When you depress and hold this button for approximately two seconds, the "Switched On" light will illuminate and power will flow to the switched outlets. To turn off the switched outlets, simply push and hold the "Switched" button again until the "Switched On" light is extinguished. Attach PureAV power cord labels to each component's power cord before you plug the cord into the corresponding outlet on the Power Conditioner. Receiver (Preamp) ­ Connect your receiver or preamp power cord to the outlet labeled "Receiver". Tape ­ Connect your tape player power cord to the outlet labeled "Tape". CD ­ Connect your CD player power cord to the outlet labeled "CD". Auxiliary 01 ­ This outlet can be used to connect any other audio equipment you may have. Amp ­ Connect your main amplifier power cord to the outlet labeled "High Current AMP". This outlet is specifically designed to deliver high current to power-hungry amplifiers. (The PF40L has two high-current outlets for a secondary amp. ) PureAV Power Conditioner Step 3 Connect Video Components to the Video Filter (always on) Certain components should be powered at all times. For this reason, the video filter outlets are "always on" or un-switched, and constantly receive power as long as the Power Conditioner is plugged into an AC power source (wall outlet). Attach PureAV power cord labels to each component's power cord before you plug the cord into the corresponding outlet on the Power Conditioner. Cable/Satellite ­ Connect your cable or satellite receiver power cord to the outlet labeled "Cable/SAT". VCR ­ Connect your VCR power cord to the outlet labeled "VCR". DVD ­ Connect your DVD power cord to the outlet labeled "DVD". [. . . ] The Power Conditioner is not designed to handle current loads larger than 15 Amps or 1800 watts. Try unplugging some devices and resetting the circuit breaker (see below) located on the end of the Power Conditioner. · To reset the circuit breaker: Wait at least 10 minutes after the circuit breaker was tripped before attempting to reset the breaker. Press in the button located next to the power cord on the end of the unit to reset. [. . . ]