User manual BELKIN OMNIVIEW E SERIES KVM SWITCH

[. . . ] The E Series KVM Switch is compatible with CPUs running on, but not limited to, the following OS platforms: · An optional 9V 600mA power supply is available (Belkin Part number F1D084PWR-EUR (With Schuko Plug) and F1D084-PWR-EUR (With UK Plug)). This is only required in rare cases where the power output from the connected computer is not adequate to power the KVM Switch. : Enclosure: Power: F1DB102P2, F1DB104P2 High-impact plastic By PS/2 computer keyboard port; optional 9V DC, 600mA power adapter, center-pin-positive polarity 2 and 4 respectively for 2- and 4-port models CRT and LCD (with VGA support) Up to 1920x1440 @ 75Hz PS/2 (miniDIN6) PS/2 (miniDIN6) VGA (HDDB15 female) HDDB15 female 32° to 104° F (0~40° C) -4° to 140° F (20~60° C) 0-80% RH, non-condensing 2 years (F1DB102P2) 5. Where you place the KVM Switch will be based on the location of your CPUs and the length of your cables. [. . . ] You can directly select which computer you wish to control by pressing the direct-access port selector next to the corresponding port. Note: The port LED will remain solid for some computers that continuously supply power to the keyboard PS/2 port even while they are shut down. In AutoScan mode, the E Series KVM Switch remains on one active port for five seconds before switching to the next active port. to activate the AutoScan function , press "Scroll Lock" , "Scroll Lock" , "0". To stop AutoScan, press any button on the front panel or any key on the keyboard. If the user is using the mouse or keyboard when the E Series KVM Switch is switching between ports, data flow may become interrupted and could result in erratic mouse movement and/or wrong-character input when using the keyboard. Below is a complete list of hot-key commands that can be used for your E Series KVM Switch: Note: Each command needs to be preceded by "Scroll Lock", "Scroll Lock". Note: You will have approximately three seconds to complete each hot-key sequence. A: The E Series KVM Switch will support any operating system that runs on a PS/2 platform only. A: The KVM Switch can be placed up to 25 feet away from your PS/2 computer. A: No, the KVM Switch does not require any drivers or software to be installed in your computers. Simply connect all your computers to the Belkin KVM Cable Kits, and then attach one keyboard, monitor, and mouse to the console port, and it is ready for use. A: No, the KVM Switch can be used in the majority of cases without an external power adapter. A: No, the KVM Switch must be connected to both the video and keyboard/ mouse ports on your computers. The KVM Switch detects the power from the PS/2 ports on your computers in order to function. A: Yes, the KVM Switch works with Red Hat and other Linux distributions configured for PS/2 support. My computer does not boot up when connected to the KVM Switch, but works fine when I connect the keyboard, video, and mouse directly to the computer. ⷠMake sure that the keyboard and mouse cables are connected tightly between the KVM Switch and the computer. Check that the monitor you are using supports the resolution and refreshrate setting on your computer. Check that the graphics card you are using supports the resolution and refresh-rate setting on your computer. ⷠConnect the monitor directly into the computer with which you are having trouble to see if the problem still appears. ⷠConnect your monitor directly to the computer to verify that your monitor is functioning properly. [. . . ] Port: An interface receptor on a computer through which you can attach a device or plug in a device cable. , of 501 West Walnut Street, Compton CA 90220, declare under our sole responsibility that the products: F1DB102P2, F1DB104P2 to which this declaration relates: Comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. , declare under our sole responsibility that the products F1DB102P2, F1DB104P2, to which this declaration relates, are in conformity with Emissions Standard EN55022 and with Immunity Standard EN55024, LVP EN61000-3-2, and EN61000-3-3. [. . . ]