User manual BELKIN F6C500-USB

[. . . ] 3. 11 BATTERY BACK-UP OUTLET Data-sensitive equipment, such as a computer, monitor, and external drive should be powered by these outlets. Power (utility or battery) is not supplied to these outlets when the UPS is switched off. (Do not plug surge protectors or power strips into the battery back-up outlets. ) 3. 12 SURGE-ONLY PROTECTED OUTLETS Equipment such as a printer, fax machine, scanner, or desk lamp should be powered by these outlets. These outlets are always on (when utility power is available) and are not controlled by the front panel switches. Operation (continued) Note: During the self-test, the UPS briefly operates the loads on-battery (the onbattery LED comes on). [. . . ] Connect the Loads Plug the loads into the output connectors on the rear of the UPS. To use the UPS as a master on/off switch, make sure all of the loads are switched on. Cable Management It is used to corral all of the power cords into a neat and safe order. It also assists in preventing accidental cord detachment. 4. 1 4. 2 Safety CAUTION!To reduce the risk of electric shock, disconnect the UPS from the main power supply before installing a computer interface signal cable. Reconnect the power cord only after signaling interconnections have been made. 4. 3 4. 4 CAUTION: Use only a factory supplied or authorized UPS monitoring cable!7. 2 USB (Universal Serial Bus): HID (Human Interface Device) setup procedure 1. When the USB cable that comes with the UPS is first connected to a USB port on your computer, the Windows® 98 dialog called "ADD NEW HARDWARE WIZARD" should appear automatically. (To display this dialog manually, you can choose the Start button and then "Settings" to access the Control Panel and then double-click "ADD NEW HARDWARE". The "ADD NEW HARDWARE WIZARD" dialog box guides you through the installation process. A dialog states "Windows will now search for any new Plug-and-Play devices on your system". A subsequent dialog gives you these options: · Search for the best driver for your device (recommended). · Display a list of all drivers in specific location, so you can select the driver you want. The Wizard will then search your hard drive for a file called. . . . \INF\hiddev. inf. This file contains all the information that Windows® 98 needs to install the correct device drivers. The installation process will continue automatically until a dialog displays indicating that the drivers have been installed. Select the "Finish" button and your drivers are installed. CAUTION!The internal energy source (the battery) cannot be de-energized by the user. The output may be energized when the unit is not connected to a main power supply, thus, a shock hazard may be present. (RISK OF ELECTRIC SHOCK) HAZARDOUS LIVE PARTS INSIDE THIS UNIT ARE ENERGIZED FROM THE BATTERY SUPPLY EVEN WHEN THE INPUT AC POWER IS NOT CONNECTED. NO USER SERVICEABLE PARTS INSIDE, PLEASE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. [. . . ] Breaker for overload and short circuit protection Single Line (2-Wire, RJ11) Network (UTP, RJ45) compatible jacks, one input/two output except F6C325 (Series) UPS output cut off immediately or input breaker protection Sealed, maintenance-free lead acid 4 hours (to 90% of full capacity) Automatic self-test and discharge protection, replace battery indicator Depending on computer load. . . 11. 4"x9. 6"x12. 8" 10A/250V*1pcs, EN60320 10A/250V*4pcs; EN60320/F 10A/250V*4pcs; EN60320/F Slow beeping sound (about 15 sec. interval) RS232 Port (except F6C325-Series) CE, TUV, BSI, NF Meet IEEE C62. 41. Category A standard 0~95%, humidity non-condensing, 0~40°C <40dBA (1 meter from surface) -15°C ­ 40°C (with battery) -15°C ­ 70°C (without battery) ALARM BATTERY PROTECTION AND FILTERING 525VA 525VA(315W) 625VA 625VA(375W) MODEL INPUT Capacity Voltage Frequency Voltage (on battery) Frequency (on battery) Voltage Regulation AVR Transfer Time Spike Protection Overload Protection USB Series 350VA 500VA 350VA(277W) 500VA(300W) 187 Vac - 280 Vac 50Hz or 60Hz ±3Hz (auto sensing) Simulated sine wave, 230 Vac±8% 50Hz or 60Hz ±1Hz Smart boost increases 14. 8% of voltage if input is 213 to 187 Vac. [. . . ]