User manual BELKIN F5U501FEU

[. . . ] Insert the card into the PCI slot, carefully aligning the rear bracket to the computer case. Make sure that the card edge is fully inserted into the slot. 4 Installation (continued) 5. Fasten the card securely using the screw that was used to hold the rear bracket. 6. Re-attach the case of your computer. 5 Installation (continued) 7. [. . . ] As Windows® 98 boots up, it will recognize the new FireWire® card in your system. In the next dialog as shown below, select "Display a list of . . . " then click on "Next". 6 Installation (continued) 9. Select the Texas Instruments driver as shown below, then click on "Next". NOTE: If Texas Instruments is not one of the choices, click on "Show all hardware". On the screen that appears, under manufactures, select Texas Instruments then under models, select Texas Instruments OHCI Compliant IEEE 1394 Host Controller. The screen that follows is an update warning prompt, click "Yes". 7 Installation (continued) 10. Windows® will then prompt you that it has found the driver file for your FireWire® card. Please be prepared to insert this into the CD-ROM drive of your computer if necessary. When Windows® is done copying and installing the proper driver files, it will show you the final dialog below. Click on "Finish" to end. 8 Installation (continued) That's it!Now you can enjoy all the benefits of super fast 400Mbps FireWire devices on your computer. After you are done with the guided tour and Readme files, you will be asked to restart your computer. After restarting, connect your DV Digital camcorder to one of the slots on the 1394 FirePath card. Turn your camera "ON" before you start MGI Video Wave III SE. 10 Installation (continued) 10. After Launching Video Wave, click on the capture icon (see diagram below). Capture Icon 11. On the next screen that appears, click on the "Settings" button located on at the bottom right hand corner (refer to diagram below). Settings button 11 Installation (continued) 12. Under the "Capture Settings" screen set the Video Capture Device to "DVcam Capture", the Audio Capture Device to "DV Audio" then click "OK". 13. Once you are back on the "Capture Screen"(Video Wave Main screen), click the "Video+Audio" button to begin capturing. If you are in VideoWave and want to turn off the camcorder, you will need to exit VideoWave and then turn off the camcorder. Otherwise, VideoWave stops responding and you will need to exit VideoWave and restart the program to use it. Most camcorders shut down to save battery power when they are not used. [. . . ] Most camcorders shut down to save battery power when they are not used. If you are in VideoWave and this happens (you have chosen standby mode), then you will need to exit VideoWave, turn on the camcorder to record instead of standby mode if you intend to capture a long video stream (usually more than 10 minutes). 12 Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Components, of 501 West Walnut Street, Compton CA 90220, declare under our sole responsibility that the product: F5U501FEUFEU to which this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CE Declaration of Conformity We, Belkin Components, declare under our sole responsibility that the F5U501FEUFEU, to which this declaration relates, is in conformity with Generic Emissions Standard EN50081-1 and with Generic Immunity Standard EN50082-1 1992. Belkin Components Limited Lifetime Product Warranty Belkin Components warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. [. . . ]