User manual BELKIN F5U111

[. . . ] If this equipment does cause harmful interference to radio or television reception, the user will be responsible to correct the interference at his own expense. Note 1: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note 2: Shielded interface cables must be used in order to comply with the emissions limits. Contacting Belkin Components: Sales 310. 898. 1100 Technical Support 310. 898. 1100 ext. 2263 Web Site www. belkin. com sales@belkin. com E-mail Support@belkin. com Version 1. 3a September 30, 1998 Copyright 1998. [. . . ] Remove and reinstall the USB support component of the operating system. Use the Windows® Find Computer option. Wait at least 20 seconds between disconnecting and connecting devices. Be patient when Windows® is installing the Adapter (or any other USB device). Plug-and-Play operations in Windows® can sometimes take up to 30 seconds or so between apparent activities. 11 6. Troubleshooting You replaced the Ethernet Adapter with a new Ethernet Adapter and it does not work. Each Belkin USB Ethernet Adapter has a unique encoded Ethernet identifier. Unplugging the adapter from the Windows® machine, and plugging a different adapter into the same port, will cause a problem in the protocol software. The program detected that your computer is not configured for proper USB support. The solution is to upgrade your motherboard or add a USB controller card. It is possible that you do have the proper OS, but there is no connection between the motherboard and the USB connectors on the bracket. It is possible that you do have the proper OS, but the controller on the motherboard is malfunctioning. The host computer might be in standby mode, and not supplying full power to its devices. Enumerate is a USB term meaning the system has identified and configured the device and given it a unique address. Replace the Ethernet cable. The installation procedure produces the message: Hardware and software support for USB was not found. The LED is off. The LED is blinking. 10 2. Ethernet Adapter Package Dimensions: 4. 25 X 3. 75 X 1. 25 Connector (Ethernet): RJ45 Connector (USB): Series B Weight: 3. 9 oz. Power Requirements: 5 V, 200 mA (powered via the USB connection) Data Transfer Rate Can exceed 6 Mbits/s (depending on the computer, operating system, and communication protocol) Environmental Conditions Operating Range: 0 to 55 °C (32 to 131 °F) Storage Range: -20 to 80 °C (-4 to 176 °F) Humidity: 10 to 90%, non-condensing LED Flashes when the USB connection is operational. Remains steady on when both the USB and Ethernet connections are active. Memory Size 32K ( 8-bit SRAM for IN and OUT data buffers 1024-bit non-volatile configuration storage Certification FCC, Class B CE Mark Software Compatibility The Belkin Ethernet Adapter works with any standard Ethernet protocol. The supplied drivers for Microsoft Windows® 98 and Windows® 95 (OSR2. 1) support the following protocols: TCP, IPX, and NetBEUI. 3 USB Specifications 2. 2 Supplied Components The following components are included: · Belkin USB Ethernet Adapter device (Specifications are outlined in Section 7) · Belkin USB cable, 6' · Software installation diskette · Belkin USB Ethernet Adapter User Manual 2. 3 System Setup The USB cable is provided; you provide the network cable. Caution: If you choose to use a USB hub, the hub must be externally powered. In order to use the adapter, you must install drivers in the USB host PC, as described in the following sections. [. . . ] SPECIFYING THE TCP/IP PARAMETERS This configuration procedure is identical to that of other network interfaces, for example, an Ethernet card. When the Belkin USB Ethernet Adapter is the only installed network interface. Additionally, a new protocol icon with the title TCP/IP should be visible. To specify the TCP/IP parameters, use the procedures described in section C on page 9. [. . . ]