User manual BELKIN F1DZ104T

[. . . ] OmniView KVM Switch belkin. com TM Control up to four computers from one PS/2 console Belkin Corporation 501 West Walnut Street Compton · CA · 90220 · USA Tel: 310. 898. 1100 Fax: 310. 898. 1111 Belkin Components, Ltd. Express Business Park · Shipton Way · Rushden NN10 6GL · United Kingdom Tel: +44 (0) 1933 35 2000 Fax: +44 (0) 1933 31 2000 Belkin Components B. V. Starparc Building · Boeing Avenue 333 1119 PH Schiphol-Rijk · The Netherlands Tel: +31 (0) 20 654 7300 Fax: +31 (0) 20 654 7349 Belkin Components, Ltd. 7 Bowen Crescent · West Gosford NSW 2250 · Australia Tel: +61 (0) 2 4372 8600 Fax: +61 (0) 2 4372 8603 Belkin Tech Support US: 310. 898. 1100 ext. 2263 Europe: 00 800 223 55 460 Australia: 1800 666 040 User Manual SE Plus Series F1DZ102T F1DZ104T P74178 © 2002 Belkin Corporation. All trade names are registered trademarks of respective manufacturers listed. Mac and Mac OS are trademarks of Apple Computer, Inc. , registered in the U. S. [. . . ] Connect the power supply to the Master switch first and power up the Switch. You should see the Switch light up and display the digits "00", indicating its BANK address. Power up the Slave switches sequentially, beginning with BANK 01, by connecting each unit's power supply. Each switch should display its corresponding BANK address number as it is powered up. 16 INSTALLATION Note: If the Switches do not enumerate correctly, reset the Master switch (BANK 00) by simultaneously pressing the "BANK Up" and "BANK Down" buttons. You can also reset the Master switch to detect newly added Slave switches. If the switches still do not enumerate correctly, check that all switches have the correct BANK address assigned to them and that all daisy-chain cables are connected properly. Verify that the Master unit has detected all Slave switches by scrolling through the BANKs using the "BANK Up" and "BANK Down" buttons. If all Slave switches are detected properly, the LED display on the Master switch will register and display the attached Slave switch's BANK address. Example of Daisy-Chain Configuration Slave Input VGA VGA 04 VGA03 VGA 02 VGA 01 Master Input/Slave Output USB 04 USB 02 04 USB 03 03 02 USB 01 01 cable 1 Master unit (BANK 00) Slave Input VGA VGA 04 VGA03 VGA 02 VGA 01 Master Input/Slave Output USB 04 USB 02 04 USB 03 03 02 USB 01 01 cable 2 Slave Input Slave unit (BANK 01) Master Input/Slave Output VGA VGA 04 USB 04 VGA03 VGA 02 USB 02 VGA 01 04 USB 03 03 02 USB 01 01 cable 3 Slave Input Slave unit (BANK 02) Master Input/Slave Output VGA VGA 04 USB 04 VGA03 VGA 02 USB 02 VGA 01 04 USB 03 03 02 USB 01 01 Slave unit (BANK 03) Powering Up the Systems Once all cables have been connected, power up the computers that are attached to the Switch. The Switch emulates both a mouse and keyboard on each port and allows your computer to boot normally. Check to see that the keyboard, monitor, and mouse are working normally. Proceed to do this with all occupied ports to verify that all computers are connected and responding correctly. If you encounter an error, check your cable connections for that computer and reboot. If the problem persists, please refer to the Troubleshooting section of this manual. Now that you have connected your console and computers to your Switch, it is ready for use. 17 USING YOUR SWITCH Select connected computers by either the direct-access port-selectors, located on the front panel of the Switch, or hot key commands, through the console keyboard. It takes approximately 1-2 seconds for the video signal to refresh after switching computers. This is normal operation and ensures that proper synchronization is established between the console and the connected computers. Selecting a Computer Using Direct-Access Port-Selectors You can directly select which computer you wish to control by pressing the direct-access port-selector next to the corresponding port. If you are installing multiple switches that are daisy-chained, use the BANK scroll keys located on the front panel of the Master switch to access other computers that are connected to the Slave switches. Selecting a Computer Using Keyboard Hot Key Commands Switch to the next or prior port with simple keyboard key sequences using the Scroll Lock key and either the up or down arrow keys. To send commands to the Switch, the Scroll Lock key must be pressed twice within two seconds. Next, press the up or down arrow keys, and the Switch will switch to the prior port or the next port. USING YOUR SWITCH You can switch directly to any port by entering the two-digit BANK address followed by the two-digit number of the port you wish to access. [. . . ] · Check the cables and make sure that they are inserted correctly. TROUBLESHOOTING The computer boots up, but the mouse does not work. · Make sure the mouse works when directly plugged into the computer. When I switch from one port to another, mouse movement is completely erratic. · Make sure you do not have more than one mouse driver installed. [. . . ]