User manual BELKIN F1DA104T

[. . . ] OmniView PRO2 Series KVM Switch User Manual F1DA104T F1DA108T F1DA116T TM PRO2 Series 13 TABLE OF CONTENTS Overview Feature Overview . . 16 Using your PRO2 Selecting a Computer Using Keyboard Hot Key Commands AutoScan Mode . . 34 OmniView PRO2 Series KVM Switch TM Congratulations on your purchase of this Belkin OmniView PRO2 Series KVM Switch (the PRO2). Our diverse line of KVM solutions exemplifies the Belkin commitment to delivering high-quality, durable products at a reasonable price. [. . . ] Also specifies the amount of time the "Port Identification" tag displays on-screen after making a port selection. After you have selected the desired time intervals, push "Enter" key to save the entry. Press the "ESC" key to go back to the original OSD menu screen. Press the "ESC" key again to exit the On-Screen Display completely. Once you have selected a computer on the menu, press "Enter" to switch to that port. Note: If there are Slave units connected, and the AutoScan time and OSD display time settings are set on the Master unit, the settings will also apply to all slave units. Updating Firmware: To update your firmware, download the appropriate firmware file and utility from belkin. com. The utility automatically guides you through the process of updating the firmware on your PRO2. Cautions and Warnings: We strongly recommend that you update your firmware only if you are currently experiencing mouse and keyboard problems with your PRO2, as reconfiguring software may lead to unexpected operational problems. Please contact Belkin Tech Support if you need assistance. To update the firmware, you will need the following items: 1. A custom flash cable (DB25 Male-to-RJ45; included with purchase) that connects between the PRO2 and the computer. Firmware update files available at belkin. com. 21 USING YOUR PRO2 Connecting Computers: 1. Connect a keyboard, monitor, and mouse to the computer you prepared for firmware update. Connect the custom flash cable (DB25 Male-to-RJ45; included with purchase). Connect one end of DB25 to your computer's parallel port and the other end of RJ45 to the PRO2 flash upgrade jack. Setting the PRO2 into Flash Mode: The PRO2 has four Flash DIP switches: DIP Switch 1 2 3 4 ON OFF OFF OFF OFF ON OFF OFF ON ON OFF OFF OFF OFF ON OFF ON OFF ON OFF (F1DA116T Only) OFF ON ON OFF (F1DA116T Only) Firmware Main OSD Keyboard 1 Mouse 1 Keyboard 2 Mouse 2 The DIP switch should be set to the specified settings when you are attempting to update a particular firmware. For example, set DIP switch 1 to "ON" to flash update the main firmware of the switch. Note: F1DA116T requires that you flash update two firmwares for the mouse and keyboard, separately. Once the above steps have been completed, run the Flash software executable. Make sure that the appropriate Flash DIP switch is set to the "on" position. After the Flash update has been completed unplug the power supply from the PRO2. You are now ready to use your PRO2 or continue flashing a different component if necessary. 22 BELKIN KVM SWITCHES AND ACCESSORIES OmniView KVM Switches OmniView E Series. This series of desktop OmniView KVM Switches allows you to control two or four PS/2 computers from one Console and makes switching between computers more convenient. Designed for compatibility with your PS/2 platform, it reduces desktop clutter and provides a simple, reliable solution at a lower price point. The E Series KVM Switch supports high-quality resolution of up to 2048x1536@85Hz through a 400MHz bandwidth when used with coaxial VGA cabling. [. . . ] · Make sure you do not have more than one mouse driver installed. Make sure that the driver is either for a standard PS/2 mouse or a Microsoft computer-compatible PS/2 mouse. · Make sure you do not have any mouse drivers loaded in your CONFIG. SYS or AUTOEXEC. BAT files. · Avoid moving the mouse or pressing the mouse button when switching ports on the PRO2. [. . . ]