User manual BELINEA 102015

[. . . ] Please take the time to look through these instructions even if you are familiar with monitors. We have taken all possible care to ensure that this manual contains correct, accurate information. However, the manufacturer cannot assume liability for any possible errors. In addition, the manufacturer cannot guarantee that the hardware will meet the purpose you require. [. . . ] Save the original box and packing material in case you have to ship or transport the monitor. Insert the screw enclosed, tightening it with a coin or a screwdriver, so that the stand base is attached securely to the stand post. You can adjust the height of the base. MENU MENU MENU MENU SELECT/AUTO SELECT/AUTO SELECT/AUTO SELECT/AUTO Power cord Audio cable VGA cable DVI-D cable (optional) Figure 1. LCD Monitor When the base of the monitor is extended, you can tilt the monitor 90 (Pivot function). CONNECTING To connect the monitor to your PC . . . . . . . . . . . . . . . . . . . . . . . . If you have a graphic card with a digital DVI-D connector (24-pin socket), then connect one end of the DVI-D cable (optional) to the DVI-D connector of your monitor (see fig. Connection via the DVI-D interface Signal cable Figure 2a. Connecting the monitor to the power source Connecting the audio cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If your computer is equipped with an audio output port, then connect one end of the sound cable to the audio input connector of the monitor ( in fig. 3) and the other end to the Line-Out connector of the computer. To connect the monitor to the power source. . . . . . . . The monitor is equipped with a main power switch located on the back, next to the power cable socket ( in fig. First start your PC and then turn on your Belinea monitor using the power switch ( in fig. Adjust the image to meet your requirements (see the following sections "Basic Setup" and "Image settings using the OSD menu"). If there is no image displayed on the monitor, consult the section "Troubleshooting". Belinea 10 20 15 - Operating Instructions - 4 ENGLISH CONFIGURATION Monitor setup under Windows 9x/ME/2000 and XP: If using the monitor under Windows 9x/ME/2000 or XP, we strongly recommend installing the Belinea configuration file. Select the desired submenu by pressing the OSD button or ( and in fig. If you selected a submenu, now select the subfunction you want using the or OSD buttons ( and in fig. The OSD menu automatically disappears if no changes are made for more than 45 seconds (default setting). Monitor features Belinea 10 20 15 - Operating Instructions - 5 ENGLISH OSD MENU FUNCTIONS OTHER LANGUAGE OSD POSITION INPUT INFORMATION RESET ENGLISH ANALOG OFF RUN 1600x1200@60 Hz PRESET MODE Brightness/Contrast Controls the picture's contrast, brightness. Other Displays the current graphic resolution including vertical frequency as well as letting you choose from among the following settings: Language: Selects the OSD menu language: English, German, French, Spanish, Italian and Russian. The monitor allows you to make the following connections: analog graphics card via the D-Sub interface (see fig. Information: There is an optional OSD window (On/ Off) that displays the newly adjusted screen resolution settings. Resolution Notice: The optimum resolution for this monitor is 1600 1200. Color Regulates the color temperature settings. Press the SELECT/AUTO button and or to select R (red), G (green) or B (blue). [. . . ] Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Electromagnetic fields Noise emissions The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. Energy Emissions Ecology The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www. tcodevelopment. com Austria MAXDATA Computer GmbH Ignaz-Kck-Strae 9 A-1210 Wien Benelux MAXDATA Benelux B. V. [. . . ]