User manual BELINEA 101911

[. . . ] 3 Anos de Troca em Garantia On-Site 3 Jahre Vor-Ort-Austausch-Service 3 leta garancije 3 year on-site swap out warrant (UK mainland only) +49 (0) 180 5 62 94 68 ENGLISH INTRODUCTION This manual will familiarize you with the installation and use of your Belinea monitor. Please take the time to look through these instructions even if you are familiar with monitors. We have taken all possible care to ensure that this manual contains correct, accurate information. However, the manufacturer cannot assume liability for any possible errors. [. . . ] Clean the display surface only with a soft cloth, otherwise you may damage the display's coating. If the monitor is only slightly dirty, clean it using a soft, dry and antistatic cloth. Please avoid any contact with the surface (finger, pencil, etc. ) and be especially cautious during transportation since jolts and shocks can cause the screen to become scratched (always use the original packaging). WALL MOUNTING The Belinea monitor is shipped with the standard desktop configuration. However, you can optionally mount the device on a wall or on a monitor swivel arm (optional accessory). Please follow the corresponding instructions (4-hole assembly with a spacing of 75 75 mm according to the international VESA FDMI standard). Belinea 10 19 11 - Operating Instructions - 3 ENGLISH UNPACKING Power cord Carefully lift the monitor out of the packaging and make sure that all components are included (see fig. Save the original box and packing material in case you have to ship or transport the monitor. To set up the device, you must fit the monitor base together. MENU DOWN UP AUTO POWER Audio cable VGA cable DVI-D cable (optional) Figure 1. LCD Monitor CONNECTING To connect the monitor to your PC . . . . . . . . . . . . . . . . . . . . . . . . . . . If you have a graphic card with a digital DVI-D connector (24-pin socket), then connect one end of the DVI-D cable (optional) to the DVI-D connector of your monitor (see fig. 2b), the other end to the computer. AC IN D-SUB DVI AUDIO Figure 2b. Connection via the DVI-D interface AC IN D-SUB DVI AUDIO Signal cable 2 Figure 2a. Connecting the monitor to the PC AC IN D-SUB DVI AUDIO 1 Connecting the audio cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If your computer is equipped with an audio output port, then connect one end of the sound cable to the audio input in fig. 3) and the other end connector of the monitor ( to the Line-Out connector of the computer. Adjust the image to meet your requirements (see the following sections "Basic Setup" and "Image settings using the OSD menu"). If there is no image displayed on the monitor, consult the section "Troubleshooting". Belinea 10 19 11 - Operating Instructions - 4 ENGLISH CONFIGURATION Monitor setup under Windows 9x/ME/2000 and XP: If using the monitor under Windows 9x/ME/2000 or XP, we strongly recommend installing the Belinea configuration file. You can obtain this file from your Belinea dealer or download it from the MAXDATA FTP server at ftp. Here, click the "Belinea_Treiber_Driver" directory and download the Belinea. inf and README_Belinea. TXT files. Monitor setup under Windows NT 4. 0: Under Windows NT 4. 0 no separate setup file is required. The monitor allows you to make the following connections: analog graphics card via the 15-pin mini D-Sub interface (see fig. 2b). Contrast Controls the picture contrast. H Position Controls the picture's horizontal position. Recall Restores the image settings to their factory values. V Position Language Controls the picture's vertical position. [. . . ] This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO'03 Display requirements: Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www. tcodevelopment. com Austria MAXDATA Computer GmbH Ignaz-Kck-Strae 9 A-1210 Wien Benelux MAXDATA Benelux B. V. [. . . ]