User manual BEHRINGER XENYX 1202

[. . . ] 502/802/1002/1202 User Manual A50-57613-00003 XENYX XENYX 502/802/1002/1202 Important Safety Instructions 1) Read these instructions. 6) Clean only with dry cloth. * ! This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] If this happens, use the TRIM control to reduce the preamp level until the LED does not light anymore. 2. 1. 2 Equalizer All mono input channels include a 3-band equalizer, except for the 502, which is equipped with a 2-band EQ. The circuitry of the British EQs is based on the technology used in the best-known top-of-the-line consoles and providing a warm sound without any unwanted side effects. The result are extremely musical equalizers which, unlike simple equalizers, cause no side effects such as phase shifting or bandwidth limitation, even with extreme gain settings of ±15 dB. Control elements and connectors 5 XENYX 502/802/1002/1202 2. 2 Stereo channels 2. 2. 1 Stereo line inputs +4/-10 The stereo inputs of the XENYX 1002 and 1202 have an input sensitivity switch which selects between +4 dBu and -10 dBV. At -10 dBV (home-recording level), the input is more sensitive (requires less level to drive it) than at +4 dBu (studio level). 2. 3 Connector panel and main section 2. 3. 1 Send/return effects path Fig. 2. 4: Stereo line inputs LINE IN Each stereo channel has two balanced line level inputs on 1/4" jacks for left and right channels. If only the jack marked "L" (left) is used, the channel operates in mono. The stereo channels are designed to handle typical line level signals. 2. 7: FX send/return connectors 2. 2. 2 Equalizer stereo channels (802) The XENYX 802 features a stereo 3-band EQ in each stereo channel. The filter characteristics and cut-off frequencies are the same as those in the mono channels. Fig. 2. 8: FX send/return controls STEREO AUX RETURN 802 only: the STEREO AUX RETURN connectors are used to bring the output of the external effects device (whose input is derived from the aux sends) back into the console. You can instead use these connectors as additional inputs, but any effects device will then have to be brought back into the console via a normal stereo channel. This does, however, give you the ability to use the channel EQ on the effects return signal if you wish. + When using a stereo channel as effects return path, the FX control of the relevant channel should generally be turned fully down to avoid undesirable feedback. If only the left connector is used, the AUX RETURN automatically operates in mono. Use the AUX RETURN control to determine how much of the effects signal is sent to the main mix. FX SEND The FX SEND output (does not apply for 502) should be connected to the input of an external effects unit. The post-fader FX signal you created using the input channel FX controls is sent to the effects unit via the FX SENDouput. Use the FX SEND control of the main section to adjust the overall send level (1002 and 1202 only). Fig. 2. 5: The equalizer of the stereo input channels A stereo EQ is highly preferable to two mono equalizers. when working on a stereo signal, as two separate EQ's will usually produce an unwanted discrepancy between the left and right channels. 2. 2. 3 FX sends, balance and level adjustment 2. 3. 2 Monitor and main mix Fig. 2. 6: The FX send/balance/level controls FX The FX sends of the stereo channels function similar to those of the mono channels. However, since the FX send buses are both mono, a mono sum is first taken from the stereo input before it is sent to the FX bus. [. . . ] If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. Warranty claims other than those indicated above are expressly excluded. § 4 Return authorization number 1. To obtain warranty service, the buyer (or his authorized dealer) must call BEHRINGER during normal business hours BEFORE returning the product. The buyer or his authorized dealer will receive a return authorization number. [. . . ]