User manual BEHRINGER VMX1000

[. . . ] VMX1000 Users Manual Version 1. 0 August 2003 PRO MIXER ENGLISH PRO MIXER VMX1000 IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Placing the MIX control somewhere in between those two extreme positions determines the volume ratio of the two signals. If the MODE switch is in its SPLIT position (see ), the (PFL) MIX control has no function. The VOL control determines the volume of the headphone signal. + + 6 2. CONTROL ELEMENTS PRO MIXER VMX1000 2. 5 XPQ 3D surround function The XPQ 3D surround function is a built-in effect that gives your music a nice finishing touch, making every performance truly memorable. By widening the stereo base, the sound comes through more alive and transparent. Using the XPQ ON switch activates the XPQ 3D surround function (corresponding LED is lit) and the XPQ control determines the intensity of the effect. 2. 9 Connections These are the LINE and CD inputs respectively, used for connecting tape decks, CD or MD players etc. The PHONO inputs for channels 1 through 3 are intended for connecting turntables. switched over to line level (see Using the PHONO/LINE switches, you can change the input sensitivity of the PHONO inputs on channels 1 through 3 to line level (switch pressed). This way, you can even connect a tape deck or a CD player to the PHONO inputs. 2. 6 Effects loop Using the RET control, you determine the volume of the effects signal that can be brought in at the RETURN input ). To get the effects signal, you need on the rear (see to connect the inputs of an effects unit to the SEND outputs (see ) of your VMX1000. The outputs of the effects unit are then connected to the RETURN inputs of your mixer. + 2. 7 CROSSFADER section The VCA CONTROLLED CROSSFADER is used to cross fade between the selected channels (see ). Use the CF CURVE control to modify the control character of the crossfader between linear and logarythmic in an infinite number of steps. When in linear characteristic mode, the crossfader fades equally in each segment of its movement range; in the logarythmic characteristic mode, volume control is concentrated to the outer segment of the faders range of motion. Use the ASSIGN A and ASSIGN B rotary switches to determine which input signals are routed to the A and B sides of the CROSSFADER. With ASSIGN A, channels 1 through 4 can be selected; with ASSIGN B, channels 2 through 5. Then, you can alternate between these two channels using the CROSSFADER (see ). IMPORTANT: Always pay attention to the correct position of the PHONO/LINE switch when connecting a line level signal to a phono input. Otherwise, overdriving may lead to permanent damage to the phono input. The MIC AUX signal, adjustable using the AUX controls on the microphone channels (see ), is laid out at this SEND jack connector. An external stereo effects signal can be fed back into the VMX1000 using the RETURN L/R jack connectors. If you connect a mono effects signal, you need to use the left RETURN L connector. The effect volume can only be adjusted on the output control of the effects unit. Please take the time to complete and return the warranty card within 14 days of the date of purchase. [. . . ] Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. [. . . ]