User manual BEHRINGER UMX25

[. . . ] UMX25 User's Manual Version 1. 1 August 2006 U-CONTROL U-CONTROL UMX25 IMPORTANT SAFETY PRECAUTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] 3. 2: Rear panel connectors Use this socket to supply the UMX25 with current from an external power supply unit (not included). The connector (type B) on the device is connected using the cable supplied to a free slot on the host computer (where you will find a type A connector). It is compatible with the USB 1. 1 and USB 2. 0 standards. 4. 1. 1 The FACTORY MEMORY The FACTORY MEMORY is the internal memory storing the basic settings of the UMX25. The most important feature of the FACTORY MEMORY is the controller map described in point . These settings define a number of useful parameters and are automatically loaded when the device is switched on. Assignments that are modified during a session, will be discarded when the unit is switched off. In order to save the modified assignments, the UMX25 has been provided with a USER MEMORY. 8 4. OPERATION U-CONTROL UMX25 4. 1. 2 The USER MEMORY Settings that are stored in the USER MEMORY, are stored permanently in the internal flash ROM and will be retained even after switching the unit off. When you access the USER MEMORY for the first time, it stores a copy of the FACTORY MEMORY settings. As soon as you make changes to the existing controller map, they are stored automatically without your intervention. The following control element assignments including channel information can be permanently stored in the USER MEMORY: - FOOT SWITCH connector - OCTAVE SHIFT button - VOLUME/DATA fader - PITCH BEND wheel - MODULATION wheel - Rotary controls R1 ­ R8 - Buttons B1 ­ B8 Special case: If you want to assign the control element to the GLOBAL CHANNEL again, please press the 0 key next to the ENTER key (instead of the number keys 1 to 9). To discard your assignments either press the CANCEL button or the ASSIGN button again. The channel set-up of all control elements of the UMX25 is based on the GLOBAL CHANNEL. This means that a control element is always set to the GLOBAL CHANNEL until you assign a different channel to it. Whenever you change the GLOBAL CHANNEL you also change the channels assigned to the various control elements!Operate the control element whose channel shall be set to differ from the GLOBAL CHANNEL. Now the UMX25 "knows" which control element shall be assigned to a SINGLE CHANNEL. Press the button. 3) 4) 5) Now define the SINGLE CHANNEL by entering a number between 1 and 16 using the number keys. - To enter channel 4 press key . 4. 2 ASSIGN mode As already mentioned in the preceding chapters, the ASSIGN mode is a powerful tool which allows you to re-configure the UMX25 to an extremely easy-to-use controller. The fundamental logic of the assignment procedure was already presented in Chapter 3 "CONTROL ELEMENTS AND CONNECTIONS". 4. 2. 1 Setting the GLOBAL CHANNEL MIDI channels are classified into two types: one GLOBAL CHANNEL and 15 additional SINGLE CHANNELS. The GLOBAL MIDI CHANNEL is a factory setting and all MIDI instructions are sent over this channel: messages of various control elements as well as note-on and note-off messages. Please proceed as follows to modify the GLOBAL MIDI CHANNEL: 1) 2) 3) 4) Press the ASSIGN button and keep it pressed. [. . . ] Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/ adaptation shall not be considered a defect in materials or workmanship. The warranty does not cover any such modification/ adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation. [. . . ]