User manual BEHRINGER UB2442FX-PRO

[. . . ] EURORACK UB1622FX-PRO UB1832FX-PRO UB2222FX-PRO UB2442FX-PRO Users Manual Version 1. 4 February 2006 EURORACK UB1622FX-PRO/UB1832FX-PRO/UB2222FX-PRO/UB2442FX-PRO IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] SOLO The SOLO switch routes the monitor send to the solo bus (post-fader and post-mute) or to the PFL bus (pre-fader and pre-mute). The position of the MODE switch in the main section determines which of the buses is selected. AUX SEND!RET V7!!!!AYQSP STEREO AUX STEREO AUX RETURN connectors RETURN (TO AUX !STEREO AUX RETURN connectors STEREO AUX RETURN (TO AUX SEND ) control STEREO AUX RETURN !(TO AUX SEND !) control 2. 3. 5 Stereo aux return control STEREO AUX RETURN 1 The STEREO AUX RETURN 1 control determines the level of this signal in the main mix. If STEREO AUX RETURN 1 is used as effects return, this will determine the level of the effects when mixed with any dry channel signal. vhy) AUX SEND STEREO AUX RETURN !connectors + When used in this way, the effects device should be set at 100% effect. Tab. 2. 1: Connectors and controls for monitor mix with effect STEREO AUX RETURN FX On consoles UB1622FX-PRO and UB1832FX-PRO this is the STEREO AUX RETURN 2, on consoles UB2222FX-PRO and UB2442FX-PRO this is the STEREO AUX RETURN 3. Use the STEREO AUX RETURN FX control to determine the level of the signal routed from the AUX RETURN FX jacks to the main mix. If nothing is connected to these jacks, the output of the built-in effects module will appear. MAIN MIX / TO SUBS This switch routes the signal fed in via the STEREO AUX RETURN FX jacks either to the main mix (not pressed) or to the submix (pressed). On the UB2442FX-PRO you can select which subgroup the signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX / TO SUBS). Fig. 2. 12: Stereo aux return and stereo aux return (to aux send) controls STEREO AUX RETURN 1/2 (TO AUX SEND) The two right-hand STEREO AUX RETURN controls have a special function: they can be used to add an effect to a monitor mix. An example follows (UB1622FX-PRO wired to an effects device): Monitor mix with effect In this instance, your effects device should be set up as follows: the AUX SEND 2 jack should be connected to the L/Mono input of your effects device, with its outputs coming back into the STEREO AUX RETURN 1 jacks. Connect the AUX SEND 1 jack output to the amplifier of your monitor system. The AUX SEND 1 master control determines the overall volume of the monitor mix. SOLO RETURNS Additionally, this model allows you to route the aux returns together to the solo bus and the PFL bus. STEREO AUX RETURN 4 (UB2442FX-PRO only) This control behaves the same way as the other stereo aux returns. Additionally, it provides for a simple monitor path using the switch CTRL ROOM & PHONES ONLY. CTRL ROOM & PHONES ONLY Use this switch to route the signal appearing at the AUX RETURN 4 jacks to the control room and headphones outputs. 2. 3. 6 Supplement to UB1832FX-PRO The UB1832FX-PRO has a stereo fader for the AUX RETURN FX and offers a variety of routing options: MUTE disables the effect return (but not PFL of course!), SOLO routes it to the Solo or PFL busses, SUB to the subgroups and MAIN to the main mix. 2. CONTROL ELEMENTS AND CONNECTORS 9 EURORACK UB1622FX-PRO/UB1832FX-PRO/UB2222FX-PRO/UB2442FX-PRO 2. 3. 8 CD/Tape input, CD/tape output Fig. 2. 15: 2-track connectors and lamp socket CD/TAPE INPUT The CD/TAPE INPUT jacks (RCA) are designed to accept a 2-track recorder (e. g. The output signal of a second EURORACK or the BEHRINGER ULTRALINK PRO MX882 can also be connected here. [. . . ] Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. The warranty does not cover any such modification/adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation. [. . . ]