User manual BEHRINGER SL3242FX-PRO

[. . . ] EURODESK SL3242FX-PRO/SL2442FX-PRO User Manual A50-24413-00002 EURODESK SL3242FX-PRO/SL2442FX-PRO Important Safety Instructions 1) Read these instructions. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] This signal is mono because very low frequencies disperse quickly, so there would be no benefit to position this signal in the stereo mix. 2. 14: XLR main out connectors (34) The MAIN OUT(puts) are balanced XLR connectors with a nominal operating level of +4 dBu and provide the main mix signal. Fig. 2. 15: Main out connectors and main insert (35) The MAIN OUT 1/4" TRS connectors outputs also provide the main mix signal. 2. 11: Mono out fader and low-pass filter (29) The MONO fader controls the volume of the signal present at the MONO OUT (see (32)). (30) The FREQ control adjusts the cut-off frequency of the lowpass filter (30 to 200 Hz). (31) Use the LOW PASS FILTER switch to activate the filter function (LED illuminates). (36) Like the channel inserts, the MAIN INSERT connectors can be used to connect a dynamics processor or equalizer for further processing of the mix signal. The MAIN INSERT refers to the Main Outs (XLR and 1/4" TRS connectors), the MONO OUT (see (32)) and, if the MAIN switch in the PHONES/CONTROL ROOM section is pressed, also to the PHONES/CTRL ROOM output (see (46)). Fig. 2. 12: Mono out connector (32) The MONO OUT connector provides the line-level mono signal for connection to the inputs of a power amp or active speaker. In this case, the signal should of course not be limited by the low-pass filter. 2. 6 Main out section Fig. 2. 16: Level meter (37) The red "+48 V" LED illuminates when phantom power is on. Phantom power is required for the operation of condenser microphones, and can be switched on with the corresponding switch on the rear of the console. (39) The high-precision level meter accurately indicates the output signal level. For example, when you press the SOLO switch on one of the input channels, its signal level will be displayed here, either pre-fader (PFL) or post-fader (SOLO), depending on the position of the SOLO/PFL switch (see (40)). In PFL mode only the left display is active, because the PFL signals are mono. (40) The SOLO/PFL switch determines whether the monitored signal is pre (PFL) or post-fader (SOLO) after pressing the SOLO/PFL switch (the LED illuminates). When you adjust a signal with the TRIM control, it is advisable to select PFL mode, so that the level shown is independent of the channel fader position. Fig. 2. 13: Main out fader (33) Use this high-precision MAIN fader to control the output level of the main mix. 8 Control elements and connections EURODESK SL3242FX-PRO/SL2442FX-PRO 2. 6. 1 Talkback The talkback function of the EURODESK allows you to communicate with the musicians in the recording room or on the stage. The talkback signal is present at the AUX SEND outputs, which are particularly useful for monitor/headphone mixes. 2. 7 CD/tape Fig. 2. 20: CD/tape (47) TO MAIN controls the volume of, for example, a CD player connected to the CD/tape input connectors (see (49)). 2. 17: Talkback section (41) The LEVEL control determines the volume of the talkback signal at the AUX 1/2 outputs. (42) Use the TALK TO AUX 1/2 switch to activate the built-in talkback microphone. [. . . ] If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, 7. Products which do not meet the terms of this warranty will be repaired exclusively at the buyer's expense. If the buyer fails to submit a written repair order within 6 weeks after notification, BEHRINGER will return the unit. When the buyer has sent in a written repair order such costs will also be invoiced separately. § 2 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase by visiting http://www. behringer. com and kindly read the terms and conditions of our warranty carefully. [. . . ]