User manual BEHRINGER PMP5000

[. . . ] EUROPOWER PMP1000/PMP3000/PMP5000 User Manual Version 1. 0 November 2006 EUROPOWER PMP1000/PMP3000/PMP5000 IMPORTANT SAFETY INSTRUCTIONS 12) Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. 14) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. [. . . ] PMP1000: The MAIN MIX/MONITOR switch performs the same function as on the PMP3000 and PMP5000. The upper LIM LED illuminates when the internal amp protection circuit responds to levels that are too high. The LIM LEDs and the LED display do NOT light up when an external signal is fed in via the PWR AMP INSERT jacks . In all other operating modes, the minimum impedance of the speaker must not fall below 4 . 6 2 CONTROL ELEMENTS EUROPOWER PMP1000/PMP3000/PMP5000 2. 4 Main and monitor section The SURROUND control determines the effect intensity. This is a built-in effect, which widens the stereo panorama, thus making the sound more lively and transparent. Pressing the AFL switch (after-fader listening) activates the solo function. If AFL is on for the corresponding channel in the main section, you will only hear the signal from this channel. Switching AFL on has no effect on the main or monitor mix, as long as you don't move the fader. In this way, you can monitor one or several selected signals via the PHONES/ CTRL jack . This is the master send fader for the signal routed to the effects processor and to the FX SEND output (see also and ). These faders are used to set the monitor output volume (see also and ). PMP1000: The main mix allows you to control the volume from the Main 1 output with both faders. PMP3000/PMP5000: The MAIN 1 fader controls the volume of the EUROPOWER. PMP3000/PMP5000: The MONO fader controls the mono mix signal (see also ). PMP5000: The SUB FILTER filters out frequencies above the selected setting, so that only low frequencies are sent to an (active) subwoofer via the MONO OUT ). PMP5000: The SUB FREQ control determines the cut-off frequency for the subwoofer output. The PHONS/CTRL R control adjusts the headphone or control room volume (see also ). PMP3000/PMP5000: The MAIN 2 control determines the volume at the MAIN 2 output (see also ), which is the same signal as at MAIN 1, but with extra output jacks and separate volume control. PMP3000/PMP5000: With the CD/TAPE IN control you can adjust the volume of the line signal present at the CD/TAPE INPUT . PMP1000: With the CD/TAPE RET fader you can adjust the line signal applied to the CD/TAPE INPUT . Use the CD/TAPE MUTE switch to mute the channel. 2. 3 Effects section List of all multi-effects processor presets. The LED level meter on the effects module should always show a sufficiently high level. If it is constantly illuminated, the effects processor is overloading, which can lead to unpleasant distortion. [. . . ] damages/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty, the inspection costs are payable by the customer. Products which do not meet the terms of this warranty will be repaired exclusively at the buyer's expense. [. . . ]