User manual BEHRINGER FCB1010

[. . . ] MIDI FOOT CONTROLLER FCB1010 Users Manual Version 1. 5 June 2004 ENGLISH MIDI FOOT CONTROLLER FCB1010 IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Exit PRESET programming mode through keeping the DOWN/ ESCAPE key for a few seconds, or press the UP/ENTER key in order to get to the next page, where you can edit various MIDI functions for the preset selected at the beginning. + s s s s 2. 4. 5 Programming EXPRESSION PEDALS A/B s s Select the PRESET you wish to edit. Keep DOWN pressed for more than 2. 5 sec to enter PRESET programming mode. Individual MIDI functions are activated by keeping the corresponding keys pressed for a few seconds. Active MIDI functions are indicated by a permanently lit footswitch LED. 2. 4. 3 Programming program changes s s Select the PRESET you wish to edit. PROGRAMMING THE FCB1010 9 MIDI FOOT CONTROLLER FCB1010 s Activate the expression pedal you wish to program by keeping the corresponding foot key pressed for a few seconds (foot keys 8 or 9). The foot key LED blinks after you briefly press the foot key yet again. Enter the control nunmber (0 bis 127) via the footswitches or the expression pedal A. Enter the value to be transmitted when the pedal is completely open by using the foot keys or the expression pedal A. Enter the value to be transmitted when the pedal is completely pressed downward by using the foot keys or the expression pedal A. Quit PRESET programming mode by means of a long press on DOWN, or select another MIDI function for editing. 7! C-1 C0 C1 C2 C3 (Clef C) C4 C5 C6 C7 C8 G8 C-2 HD9DIrIir 0 !" # $ % & ' ( 12 24 36 48 60 (Yamaha Convention) 72 84 96 108 120 127 + s s 2. 4. 6 Programming the NOTE function The NOTE function allows you to send a MIDI note, for example, to use the tap-tempo features offered by many MIDI devices or to play sounds the same way you would on a keyboard. Keep DOWN pressed for more than 2. 5 sec to enter PRESET programming mode. Individual MIDI functions are activated by keeping the corresponding keys pressed for a few seconds. Active MIDI functions are indicated by a permanently lit footswitch LED. Keep footswitch 10/0 pressed for a few seconds to activate the NOTE function. Pressing the footswitch briefly once again makes the footswitch LED blink. Use the footswitches 1 through 10/0 or EXPRESSION PEDAL A to enter the MIDI NOTE number you wish to send with the PRESET. 2. 4: Assignment of MIDI NOTE numbers Confirm your selection by pressing UP/ENTER or cancel by pressing DOWN/ESCAPE. Select an additional MIDI function you wish to edit or exit the PRESET programming mode by keeping DOWN/ESCAPE pressed for a few seconds. s s + The NOTE function will be particularly useful for so-called taptempo applications. Many of todays multi-effects devices allow the user to enter the delay time by means of an on-board TAP button. The device measures the time between two TAP button presses and uses this interval to adjust the delay time. [. . . ] Under the terms of this warranty, BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation. Free inspections and maintenance/repair work are expressly excluded from this warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, tubes, guitar strings, illuminants and similar parts. Damages/defects caused by the following conditions are not covered by this warranty: s improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals. [. . . ]