User manual BEHRINGER FBQ3102

[. . . ] ULTRAGRAPH PRO FBQ1502/ULTRAGRAPH PRO FBQ3102/ULTRAGRAPH PRO FBQ6200 Users Manual Version 1. 1 September 2003 ULTRAGRAPH PRO FBQ1502 ULTRAGRAPH PRO FBQ3102 ULTRAGRAPH PRO FBQ6200 ENGLISH ULTRAGRAPH PRO FBQ1502/ULTRAGRAPH PRO FBQ3102/ULTRAGRAPH PRO FBQ6200 IMPORTANT SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: 1) Read these instructions. 4) Follow all instructions. CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. 5) Do not use this device near water. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] When replacing fuses, please make sure that you always use fuses of the same type. CONTROL ELEMENTS AND CONNECTORS 5 ULTRAGRAPH PRO FBQ1502/ULTRAGRAPH PRO FBQ3102/ULTRAGRAPH PRO FBQ6200 a unit intended for the European market to a 120 V power outlet, you must also replace the factory fuse with a highervalue fuse. Please take a few minutes and send to us a completely filled out warranty card within 14 days of the original date of purchase. Or fill out the warranty information online at www. behringer. com. Fig. All three equalizers in the series feature the same input and output connectors in the form of balanced 1/4" TRS and XLR connectors. The 1/4" connectors and their respective XLR connectors are wired in parallel. This balanced XLR connector provides the output signal for your subwoofer. Use the X-OVER FREQ control to select the desired crossover frequency for the subwoofer. The bandwidth limitation enacted through the highpass filter (LOW CUT) also affects the frequency response of the subwoofer output. 2. 4: FBQ6200 control elements The limiter display informs you about the amount of gain reduction perfomed by the limiter. Use the THRESHOLD control to adjust the threshold value of the limiter from -6 to +22 dB. When the control is in the -6 dB setting, the gain reduction is very pronounced; the more you turn the control toward +22 dB, the gain reduction is lower. When the threshold control is in its right-most position, the limiter is not applied. + 2. 3 Additional FBQ6200 control elements 2. 3. 1 Limiter One of the FBQ6200s outstanding features is its integrated limiter. A limiter is a device that protects your loudspeakers and other equipment connected to your FBQ6200 (or your recordings) from overdriving and the signal distortion associated. 2. 3. 2 Noise generator By using the built-in noise generator, you can create the socalled pink noise that can be used to adjust your P. A. The built-in switch illumination blinks red when the pink noise generator is activated. Use the NOISE LEVEL control to adjust the volume of the pink noise you generate. system cause some frequencies to be more prominently present while other frequencies are less present. Such a measurement of the frequency response by using a special microphone in conjunction with a real-time analyzer (a real-time analyzer is for example integrated into the BEHRINGER ULTRACURVE PRO DEQ2496) delivers the basis for setting up the equalizer. More pronounced frequencies are lowered, and those frequencies that are not so prominently featured are increased, thus approximately achieving linear reproduction. + Please take into consideration that when you increase the presence of multiple frequency bands, the overall signal level increases substantially as well. This can be avoided by performing signal corrections by lowering certain frequency ranges instead of increasing others. To produce creative sound effects, you can also purposely force the peak limiter into action. The ULTRAGRAPH PRO FBQ6200 features a built-in limiter for each channel. [. . . ] Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. [. . . ]