User manual BEHRINGER EURORACK MX3242X

[. . . ] MX3242X Users Manual Version 1. 2 May 2001 EURORACK ® www. behringer. com ENGLISH EURORACK MX3242X SAFETY INSTRUCTIONS CAUTION: To reduce the risk of electric shock, do not remove the cover (or back). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosurevoltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. [. . . ] With the buttons MON/CTRL ROOM , AUX 1 and AUX 2 , you can select the source for the headphones signal, while the LEVEL control determines the volume level. When the MON/CTRL ROOM button is pressed, the headphones output delivers the signal selected in the MON/CTRL section. Press one of the two AUX buttons to monitor the Aux Send signal on both sides of your headphones. Now the signals from Aux Sends 1 and 2 are routed to the left and rights side of your headphones respectively. + Please note that too high a monitoring level can lead to hearing damage. 2. OPERATION 19 EURORACK MX3242X 2. 4. 8 Subgroups and Main Mix fader Fig. 2. 17: Subgroups section In a recording situation, the inputs of a multi-track recorder are fed with signals from the Subgroup outputs . The 4 Subgroups, in turn, can be fed by the Main input channels and the Aux Return buses. The faders control the level of the signals routed to each Subgroup, while the MAIN MIX button sends the signal routed to a Subgroup back to the Main Mix bus. Use the PAN control to determine the signals position in the Main Mix stereo field. When the MAIN Mix button is up, the PAN control has no influence on the Subgroup signals. In live applications, Subgroups are often used to combine various groups of instruments and control their volume with one or two (stereo mode) faders. The Subgroups insert points allow for processing multiple signals with just one device (e. g. The SOLO button and its associated control LED enable you to monitor each of the 4 Subgroups individually. The MAIN MIX fader determines the level that is sent to the MAIN OUTPUTS, which are available both on ¼" phone jacks and XLR connectors . The MX3242X also routes the MAIN MIX signal to the 2-TRACK-OUT cinch jacks . OPERATION EURORACK MX3242X A very special feature of your MX3242X is its on-board Effects Processor, which offers the same hard/software quality as our well-known 19" VIRTUALIZER DSP1024P. This effects module provides 32 different standard effects such as Reverb, Chorus, Flanger, Delay, Pitch Shifter and various effects combinations. Use Aux Send 3 (Main input channels) and the Aux Send 3 master control to feed signals to the Effects Processor. Please make sure that the level read by the LED level meter in the effects module section is always high enough. To speed up preset selection, you also need The two buttons UP to press the respective opposite button. Its name can be found in the preset list printed next to the LED level meter. Aux Return 3 allows you to assign the effect signal to the Subgroups and Main Mix bus. [. . . ] Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by BEHRINGER. Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealers invoice. Any product deemed eligible for repair or replacement by BEHRINGER under the terms of this warranty will be repaired or replaced within 30 days of receipt of the product at BEHRINGER. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. [. . . ]