User manual BEHRINGER EUROLIGHT LD6230

[. . . ] When a cart is used, use caution when moving the cart/ device combination to avoid injury from stumbling over it. WARNING: This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosurevoltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. 13) Unplug this device during lightning storms or when not used for long periods of time. Servicing is required when the unit has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the device, the unit has been exposed to rain or moisture, does not operate normally, or has been dropped. 2 INSTALLATION INSTRUCTIONS EUROLIGHT LD6230 The BEHRINGER EUROLIGHT LD6230 Dimmer Pack was developed to meet the highest demands of light engineering. [. . . ] To effectively limit harmonic currents and avoid voltage fluctuations that could affect other electrical appliances, connect this equipment to an AC outlet that complies with all applicable technical standards. In all other cases, contact your local power supply provider for advice prior to usage. Defective fuses must be replaced with fuses with identical rating! The LD6230 is a Class I device in which a low-Ohm protective ground wire is an integral part of its safety design. During the installation, make sure that a low-Ohm protective conductor (< 0, 1 Ohm) exists between all bare metal parts and the grounding on the main connector. Quhr L1 L2 L3 Ppuhry 8C CH 2 8C" X X X CH 4 X 8C$ CH 6 + + X X * Activation of control electronics and respective output channel CONNECTOR TERMINAL STRIP The connector terminal strip of your LD6230 is laid out for cables with diameters between 0. 326 mm 2 (AWG 22) and 4 mm2 (AWG 12). When using flexible access lines, cable end contacts corresponding to manufacturer specifications have to be used. During the installation, all applicable national standards need to be adhered to. + + + MAINS/ILLUMINANT CONNECTORS To facilitate additional flexibility, your dimmer pack has a connector terminal strip. Cable bushings for connecting to the mains and your illuminants are located in the back. Flexibility is further enhanced with the option to retrofit a CEE connector and a 16-pin HARTING connector. Both fixed and mobile installations require compliance with IEC 61010-1:2001 (EN 6110-1:2001). In particular, a 3-phase separator (pursuant IEC60947-1 and IEC60947-3) needs to be included in the installation. This separator needs to be labeled according to IEC 60417-50008 and IEC 0417-5007. To assure compliance with Directive 89/336/EEC, only use specified upstream line filters with your EUROLIGHT. Using it without line filters specified by BEHRINGER may lead to electromagnetic interference. More detailed information on this subject can be found at www. behringer. com. Illustration: LD6230 connector terminal strip When your LD6230 leaves the assembly plant, all incoming and outgoing neutral conductor connectors are bridged. The incoming phases L1/L1, L2/L2 and L3/L3 are always connected to one another in pairs and switched to the overload protection of the channels 1 to 6. The green-yellow conductors (PE) may only be used as protective conductors. 3 INSTALLATION INSTRUCTIONS EUROLIGHT LD6230 The lowest cable gauge between L1 and L3, incoming neutral conductor (N) and protective earth (PE) is 4 mm 2 (AWG 12). For outgoing channels E1 to E6, use cables with gauges corresponding to the loads used (2. 5 mm2 (AWG 14) or 1. 5 mm2 (AWG 16)). Phrrb6d 6 - 10 13 - 16 18 - 25 Ivhyp 6XB rpvbd@V VT6 1. 5 2. 5 4 16 14 12 + + + During the installation, please adhere to all manufacturer instructions. Regardless from mains supply voltage, the maximum output current of the EUROLIGHT LD6230 is 10 A per dimmer circle. Please make sure that each dimmer load is connected to a separate channel. [. . . ] (9. 2 kg) BEHRINGER continuously strives to assure the highest quality standards possible. Technical data and the appearance of the unit may deviate from the above values and/or illustrations. 4 INSTALLATION INSTRUCTIONS EUROLIGHT LD6230 Technical specifications and appearance subject to change without notice. The names of companies, institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners. [. . . ]